I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Pic Kit-2 Programmer
₹2,400.00 Original price was: ₹2,400.00.₹2,200.00Current price is: ₹2,200.00. inc. GST
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
The PICkit 2 Development Programmer/Debugger was designed as a low-cost development tool with an easy-to-use interface for programming and debugging Microchip’s Flash families of microcontrollers. This programmer is capable of programming all current 8-, 16-, and 32-bit Flash PIC microcontrollers. And also includes the UART Tool and Logic Tool microcontroller development utilities.
Microchip’s PICKit2 is designed as much more comfortable, reliable, and powerful than the other programmers all over the internet. It is a USB-based ICSP (In-Circuit Serial Programming) programmer. As PICKit2 is a USB-powered device, it gets power from a PC USB +5V power supply. Meanwhile, the soul of the PICKit2 is the USB microcontroller PIC18F2550. The USB Data+ and Data- from the PC connected to the D+ and D- pins of the PIC182550. Moreover, using a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller. It is made up of high-quality PCB FR4 Grade with FPT Certified. This programmer module supports the following device families:
- PIC10F
- PIC12F
- PIC16F
- PIC18F
- PIC24

Related products
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
89C2051 Atmel Microcontroller IC
- Core Processor: 8051
- Data Bus Width: 8 bit
- Maximum Clock Frequency: 24 MHz
- Program Memory Size: 2 KB
- Program Memory Type: Flash
- Supply Voltage Range: 4 V to 6 V
- Package: PDIP-20
- Compatible with MCS-51â„¢ Products
- 2K Bytes of Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles
- 7V to 6V Operating Range
- Fully Static Operation: 0 Hz to 24 MHz
- Two-level Program Memory Lock
- 128 x 8-bit Internal RAM
- 15 Programmable I/O Lines
- Two 16-bit Timer/Counters
- Six Interrupt Sources
- Programmable Serial UART Channel
- Direct LED Drive Outputs
- On-chip Analog Comparator
- Low-power Idle and Power-down Modes
AVR ISP 10 Pin to 6 Pin Adapter Board
CH375B U-DISK Read Write Module USB interface communication SPI interface
PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
RS232 TO RS485 CONVERTER ADAPTER
- Input: USB 2.0 Protocol
- Output: RS232 on DB9 Male connector compatible to PC RS485/RS422 on the terminal block.
- Communication Speed: 300bps to 230Kbps.
- Auto direction control for RS485- 2W data transmission.
- Plug-and-Play (Device is Hot-pluggable)
- Cable: USB 2.0 type A to type B cable.
- Galvanic Isolation of 1.5kV
- RS232/RS485 line protection: +/- 15kV ESD.
- LED Indication for Transmit Receive signals.
- Input power from the USB port
- No external power is required.
- RS232 with DB9 Female connector
- RS485 with DB9 Male connector
- Baud rate up to 230Kbps.
- Input power supply range 9-6V DC to 26.4V DC
- USB Drivers provided for Win XP, Vista, Win7, Win8
- Working Modes: Asynchronous, half-duplex, differential transmission
- Operating temperature: -10°C to 85°C,
- Relative humidity: 5% to 95%
- Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232)
- Transmission Media: Common wire, double wire, UTP or Shielding Line
- Serial Port Feature: Compatible with EIA/TIA RS-232C standard and RS-485 standard
- Weight: 49gm
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.

Reviews
There are no reviews yet.