6A Micro Switch With Roller Arm
2TR Heat Sink
8 Pin RMC Connector
6 Pin RMC Connector
5 Pin RMC Connector
4 Pin RMC Connector
Insulation Cotton Washer for TEC1- 12706 Thermoelectric Cooler Peltier
Raspberry pi 4 case – acrylic clear
- 6-piece Acrylic case with access to all Ports on pi 4
- Compatible for All variants of the Raspberry pi 4 Model B
- Easy to assemble without any Screws or Nut-Bolts
- Slots to route GPIO and CSI ribbon cable
- Cut-out for micro SC card at the bottom panel
- Mounting holes and anti-slip rubber feet at the back.
1.3″ OLED Display I2C 128*64 display module Blue 4pin
24V 40W Ceramic Cartridge Heater Wire For 3D Printer
- Voltage: 24V, Power: 40W
- Material: 304 Stainless Steel
- Wire Length :1M
- Diameter: 6mm
- Length: 20 mm
- Works on many 3D printers, including RepRap and Prusa models.
- It fits nicely in our extruder, so it’s an easy replacement.
- Small but powerful.
- Get your hotend hot quickly.
- This unit is a more powerful unit than the standard unit for many 3D printers.
PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit
- Type: Debugger/Programmer
- Tool/Board Application: Debugging/Programming
- MCU Supported Families: Flash-based PIC MCUs
- Core Architecture: PIC, dsPIC
- IC Product Type: In-Circuit Debugger
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Supports low voltage to 2.0 volts (2.0v to 6.0v range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of the microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Easy to use Windows-based programming
- USB Interface
Pixhawk 2.4.8 Drone Flight Controller PX4 32 Bit Autopilot
- The advanced 32-bit ARM CortexM4 high-performance processors; can run NuttX RTOS real-time operating system.
- 14 PWM / servo output.
- Bus interface (UART, I2C, SPI, CAN).
- The integrated backup power and backup controller fails; the primary controller fails over to the backup control is safe.
- Provide automatic and manual modes.
- Provide redundant power input and failover.
- Multicolor LED lights.
- Provide a multi-tone buzzer Interface.
- Micro SD card to record flight data.
- 32bit STM32F427 Cortex M4 core with FPU.
- 32-bit STM32F103 failsafe co-processor.
- 168 MHz.
- 128 KB RAM.
- 2 MB Flash.
- ST Micro L3GD20H 16 bit gyroscope.
- ST Micro X4HBA 303H 14-bit accelerometer/magnetometer.
- Invensense MPU 6000 3-axis accelerometer/gyroscope.
- MEAS MS5607 barometer.
- 5* UART, 1*compatible high voltage, 2*hardware flow control
- 2*CAN
- Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
- Futaba SBUS compatible input and output
- PPM signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6VADC
- input External USB MICRO interface
- Color:Black
- Size: 50x81x16mm