MB102 Breadboard Power Supply Module converts 6.5–12V DC input to stable 3.3V and 5V DC outputs. Easily plugs into MB102 breadboards, ideal for Arduino, IoT, and electronics prototyping.
MAX485 to TTL RS485 converter module
MAX485 TTL TO RS-485 MODULE
- Operating voltage: 5V
- On board MAX485 chip
- Slew rate limited transceiver
- All the pins of the chip are controlled by the microcontroller
- use differential signalling for immunity
- 120R terminating resistor
- Power LED indication
- Distances up to 1200 meters
- Use differential signalling for noise immunity
- Speeds up to 2.5Mbit/Sec
- Multi-drop supports up to 32 devices on the same bus
- Low power consumption
- On-board 5.08mm pitch 2P terminal to facilitate RS-485
- DIMENSION: 44*14mm
MAX6675 K-TYPE THERMOCOUPLE TEMPERATURE SENSOR
- Internal integrated cold junction compensated circuit
- Operating voltage: 3V to 5.5V
- Temperature signal converted to 12-bit signal
- Thermocouple break detection circuitry
- 25-degree resolution
- K-type temperature probe
- Simple SPI serial output temperature.
- High impedance differential inputs.
- 2000v ESD signal
- Temperature range: 0 degrees to 1024 degrees Celsius
- Temperature measurement accuracy: +/-1.5 C
MAX7219 4-in-1 LED Dot Matrix Display Module
MAX7219 Dot Led Matrix Module 4 In 1 Display with 5P Line Module For Arduino Micro-controller
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Requires only 3 communication wires of MCU
- Pre-cascaded MAX7219 Dot Matrix LED Module.
- The overall size of the display is very compact
- With 64 fixing screw holes, hole diameter: 3mm.
- M3 holes for mounting.
- Module with input and output interfaces
- Support for cascading multiple modules
- Quite large display
- Display Dimensions: 32x32x6 mm
- PCD Dimensions: 128×32mm
- Weight: 55 gm
MAX7219 led module 8 digit 7 segment display
- Power: 5V
- Colour: Red/Blue (This colour means the colour of the board, not the LED)
- Material: PCB + Electronic Components
- MAX7219 digital display control module
- This module is compatible with 5V and 3.3V microcontrollers.
- You can use it for Arduino
- Only three IO ports are used to drive the eight-digit display. MAX7219 supports flicker-free displays as well as cascading displays.
MAX7219 Mini Dot Matrix LED Display Module
Maximum Demand Meters (EMS Series)
Key Features:
-
Measures maximum demand accurately over defined intervals
-
Supports single and three-phase systems
-
High-brightness digital display for clear readings
-
Data logging and real-time monitoring
-
Easy installation and configuration
-
Suitable for industrial and commercial environments
Applications:
-
Industrial power monitoring
-
Commercial energy management
-
Utility metering and analysis
-
Load optimization and control
MB-102 840 POINT BREADBOARD
- Compatible with MB-102 breadboard power supply module
- Quick circuit testing and mock-up
- 840 Contact Points
- Suitable for most IC’s, Standard 0.1′ Spacing
- Positive and Negative Power Rails on Top and Bottom
- 100% brand new and high quality
- Solderless breadboard
- Completely reusable and have a self-adhesive back
- Easy component placement
- Weight: 200 g
- Dimensions: 165 × 55 × 10 cm
MBR10100 Dual Diode 10A 100V
- Maximum repetitive peak reverse voltage VRRM: 100V
- Working peak reverse voltage VRWM: 100V
- Maximum DC blocking voltage VDC: 100V
- Voltage rate of change (rated VR) dV/dt = 10 000 V/µs
- Guard–Ring for Stress Protection
- Â Low Forward Voltage
- 150°C Operating Junction Temperature
- Â Guaranteed Reverse Avalanche
-  Epoxy Meets UL94, VO at 1/8″
- Â Low Power Loss/High Efficiency
- High Surge Capacity
- Â Low Stored Charge Majority Carrier Conduction
MBR3045 Dual Diode
- Maximum recurrent peak reverse voltage VRRM: 45V
- Maximum RMS Voltage VRMS: 31.5V
- Maximum DC blocking voltage VDC: 45V
- Power pack
- Guarding for overvoltage protection
- Lower power losses, high efficiency
- Low forward voltage drop
- High forward surge capability
- High frequency operation
- Solder dip 275 °C max., 10 s, per JESD 22-B106