MEGA8515 Atmel Microcontroller IC
- Flash (Kbytes):8 Kbytes
- Pin Count: 44
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 35
- Ext Interrupts: 3
- SPI: 1
- UART: 1
- SRAM (Kbytes): 0.5
- EEPROM (Bytes): 512
- Operating Voltage (Vcc): 2.7 to 5.5
- Package: PDIP 40P6 40
- High-performance, Low-power AVR® 8-bit Microcontroller
- RISC Architecture
- Non-volatile Program and Data Memories
- Peripheral Features includes One 8-bit Timer/Counter with Separate Prescaler and Compare Mode ,One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode, Three PWM Channels , Programmable Serial USART , Master/Slave SPI Serial Interface
- Operating Voltages – 2.7 - 5.5V for ATmega8515L , 4.5 - 5.5V for ATmega8515
MEGA8A Atmel Microcontroller IC
- Flash (Kbytes): 8 Kbytes
- Pin Count: 28
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 23
- Ext Interrupts: 2
- SPI: 1
- UART: 1
- ADC channels: 6
- SRAM (bytes): 1024
- EEPROM (Bytes): 512
- Operating Voltage (Vcc): 2.7 to 5.5 V
- High-performance, Low-power Atmel®AVR® 8-bit Microcontroller
- Advanced RISC Architecture
- High Endurance Non-volatile Memory segments
- Â Power-on Reset and Programmable Brown-out Detection , Internal Calibrated RC Oscillator ,External and Internal Interrupt Sources ,Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby.
- Operating Voltages – 2.7V - 5.5V (ATmega8L) , 4.5V - 5.5V (ATmega8
MEMS Microphone Breakout – INMP401 (ADMP401)
- -3dB roll off at 100Hz and 15kHz
- supply voltage: 1.5 to 3.3VDC
- Should comfortably output 40mW
- SNR of -62dBA
- Should comfortably output 40mW
- Omnidirectional MEMS microphone
- High SNR
- Sensitivity of −42 dBV
- Low current consumption of <250 μA
- Single-ended analogue output
- High PSRR of 70 dB
- Compatible with Sn/Pb and Pb-free solder processes
- 72 mm × 3.76 mm × 1.0 mm surface-mount package
MEPUNO COMMUNICATION BOARD
- Microcontroller ATMEGA328 P
- Crystal for microcontroller: 16 MHZ
- USB type B connector
- On-Board Power LED Indicator
- 5volt, 12 volt regulated circuit
- Two separate regulated 5volt power supply
- On Board On/Off switch
- On Board DC jack for powering up using adaptors
- On Board Reset Switch
- On Board TX/RX indication LEDs
- On board FTDI Driver for adruino
- Berg headers for external interfacing
- Supports I2C /GSM /GPS/RF/USART serial communication
- Separate berg headers available for PIR, Servo motor, RTC/I2C, GPS_TTL, and USART-TTL
- Four 3pin PBT Connectors
- Four SPDT 12V Relays
- Onboard DB9 connectors for GPS, GSM and USART communication
- Berg slot for 16x4 LCD connections
- Onboard TRIM-POT for LCD
- Onboard RTC IC: IN1307 with crystal 32768 MHZ crystal and CR2302 battery
MEPUNO ROBOT CONTROLLER BOARD
- Microcontroller ATMEGA328 P.
- Crystal for the microcontroller: 16 MHZ
- USB type B connector
- 5volt, 12 volts regulated circuit.
- Two separate regulated 5volt power supplies.
- On-Board On/Off switch.
- OnBoard DC jack for powering up using adaptors.
- On-Board Reset Switch.
- Onboard L293D dual DC motor driver.
- Onboard TSOP IR receiver.
- On Board 3 user LEDs (with jumper selection), TX/RX indication LEDs.
- On-board connectors for analogue interfacing.
- On Board Buzzer Interface.
- Â On-Board PWM Interfacing.
- On board FTDI Driver for adruino.
- Â Berg headers for external interfacing.
- Supports I2C /3 WIRE /RF/USART serial communication standards.
METAL ARM GRIPPER SERVO SG 90
METAL CHASSIS BIG
Metal Detector Sensor
- Low battery indicator
- Multiple Modes
- VCC 9V Battery
- Logic high output with common ground
- Can detect any metal at the range of 1Cm to 3Cm, you can connect a 9V battery to make it handy
- It will not detect coins if it is in the middle of the coil, it may detect if it is close to the coil, It will not detect any type of explosives
- The metal sensor has to supply 12V from controllers and not 12V via adapter
Metal Foot Pedal Switch
Metal Gear Servo Motor GS-5515MG
- Control System: Positive PWM control (1500 usec neutral)
- Operation Voltage Range: 4.8V - 0V
- Operation Temperature Range: -20 C - +60 degree C
- Test Voltage:
- Standing Torque@ 4.8V: 13kg-cm
- Speed@ 4.8V : 0.31 sec / 60 at no load
- Idle Current@ 4.8V: 250mA at stopped
- Running Current@ 4.8V: 2000mA at no load
- Standing Torque@ 6.0V: 15kg-cm
- Speed@ 6.0V: 0.28 sec / 60 at no load
- Idle Current@ 6.0V: 300mA at stopped
- Running Current@ 6.0V: 2200mA at no load
- Dead Band Width: 8 usec
- Circle: 10000 times
- Direction: Re-clock wise/ pulse travel 1500 to 1900 usec
- Drive type: FET drive
- Motor Type: Carbon brush
- Size: 41.2*20.2*37.7 mm
- Weight: 63g without splined horn
- Ball Bearing: Double ball bearing
- Gear Material: Metal gear
- Case Material: Nylon plus fiber
- Connector Wire Length: 300mm
- Connector Wire Gauge: 22AWG heavy duty (Futaba universal)
Metal mechanical Arm Gripper claw
- Metal Gripper Robotic Arm
- Operating Voltage: 4.8V to 6.6V
- Material: Aluminum Alloy
- The Kit comes with hardware, unassembly
- Clamp Max open: 55mm
- Clamp total length:108mm
- Clamp total width:98mm (when the Clamp open
- Light weight plank kit
- Compatible with HS322, HS422, MG995, SG5010 servo
- Degree of Freedom (DOF): 2
- Bearing Type: Ball Bearing
- Weight: About 68g