Blade Propeller for 8520 8.5x20mm
- Length: 8.5″.
- Pitch: 20″.
- Diameter: 55mm
- Centre hole diameter: 0.97mm
- Colour : Black & Red
- suitable for 90mm-150mm DIY Micro Quadcopter Frame Kits
- Suitable for 1mm shaft diameter Coreless motor 7*16mm, 7*20mm, 8.5*20mm
- Suitable for 1mm shaft diameter Carbon Brush motor N20, M20, N30
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
Nano V3 Ethernet Shield
NANO / UNO Multi-Purpose Expansion Board
- The Sensor Shield makes your connections with the Arduino Nano much easier
- It is compatible with Arduino Nano 2.0 and 3.0
- The shield has up to 8 analogue pins, 13 digital I/O pins, and Aref with 3 pin connectors (GND, Vcc, Signal).
- Consists of an independent I2C port with 4pins (SDA, SCL, GND, and Vcc) and UART (Rx, Tx, Vcc, and GND).
- Reset button onboard and a female jack for external power supply
- Material: FR-4 Epoxy Glass Fibre Board
- IO port leads all digital and analogue IO ports, each IO port has positive and negative power supply interface standards.
- Leads to an I2C interface on the motherboard, convenient and I2C devices connected.
- Size: Approx. 57x53x8mm
L298P Motor Shield motor driver
- L298P based Arduino motor driver shield
- Operating Voltage 5V to 12V
- Motor controller L298P, Drives 2 DC motors or 1 stepper motor
- The logical part of the input voltage VD: 5V
- Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input
- The logical part of the work current Iss:<36mA
- Driven part of the operating current Io:<2A
- Current sensing 1.65V/A
- Free running stop and brake function
- Maximum power dissipation: 25W (T = 75 Celsius)
- Max current 2A per channel or 4A max (with external power supply)
- Control signal input level: High 2.3V
- Onboard Bluetooth interface, you can directly plug, no wiring required.
- The board with L298P motor drive chip, directly with the motherboard digital I/O port (D10, D11, D12, D13), without cumbersome wiring.
- Onboard buzzer (D4), you can set the reverse alarm ringtones.
- D2, D3, D5, D6, D7, D9 are not occupied by the digital interface.
- A 0 – A 5 six analogue interfaces.
- Forward and Backward steering are indicators
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)
Arduino CNC Shield
- Shield type:Â Arduino Nano
- Firmware:Â GRBL
- Modular stepper motor drivers:Â 3
- Limit switches:Â 6
- Micro-stepping:Â 1/16
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.51
Lead Copper Nut 8mm
145 mm Trapezoidal Lead Screw
Non Unite 350W MY1016Z3 24V GearedMotor (Copy)
- Model: Non UNITEMOTOR MY1016Z3
- Name: 24V/36V DC Brushed Motor
- Rated Voltage: 24V DC / 36V DC
- Power 350W
- Rated Speed: 24VDC: 3000RPM. 36VDC: 3200RPM.
- No load speed : 3850RPM
- Gear Ratio: 1:9.78
- Rated Torque: 1.11N.m
- Sprocket: 9mm Pitch,
- Pitch: 12.7mm.
- Gear Ratio: 1:9.78
- Installation type: Motor With Foot Stand.
- Easy Install.
- Suit Controller: 24/36v 350w brush controller
- Usage: Electric Bike ,E-tricycle, Electric chairwheel,E-Scooter,E-Motocycle,DIY
470nf 100V 5mm Pitch Box Capacitor
MOQ : 3 NOS
- Capacitance: 470nf
- Voltage Rating: 100V
- Pitch: 5mm
- Dielectric Type: Double Metallized PP
- Capacitance Tolerance: ± 10%
- Capacitor Case Style: Radial Box
- Capacitor Terminals: Radial Leaded
- Operating Temperature Min: -55°C
- Operating Temperature Max: 105°C
- Automotive Qualification Standard
- High Accuracy, Long-Life Polyester Film Capacitor
- Low Leakage
- Easy Mounting
4.7nf 63V 5mm Pitch Capacitor
MOQ : 5 NOS
- Capacitance: 4.7nf
- Voltage Rating: 63V
- Pitch: 5mm
- Dielectric Type: Double Metallized PP
- Capacitance Tolerance: ± 5%
- Capacitor Case Style: Radial Box
- Capacitor Terminals: Radial Leaded
- Operating Temperature Min: -55°C
- Operating Temperature Max: 105°C
- Automotive Qualification Standard
- High Accuracy, Long-Life Polyester Film Capacitor
- Low Leakage
- Easy Mounting
3.3nf 63V 5mm Pitch Box Capacitor
MOQ :5 NOS
- Capacitance: 3.3nf
- Voltage Rating: 63V
- Pitch: 5mm
- Dielectric Type: Double Metallized PP
- Capacitance Tolerance: ± 5%
- Capacitor Case Style: Radial Box
- Capacitor Terminals: Radial Leaded
- Operating Temperature Min: -55°C
- Operating Temperature Max: 105°C
- Automotive Qualification Standard
- High Accuracy, Long-Life Polyester Film Capacitor
- Low Leakage
- Easy Mounting