Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)
- Driver Model: VNH3ASP30
- Current sensing available to Arduino analogue pin
- Operating Voltage: 12 V to 16V DC
- Peak Current: 14A
- Continuous Current: 30A
- of Channels: 2
- Maximum PWM frequency: 20 kHz
- MOSFET on-resistance: 19 m (per leg)
- Thermal Shutdown protection
- Under-voltage and Overvoltage shutdown.
- LED Indicator
- Dimensions: 60 x 54 x 12mm
- Weight: 19gm
ESP8266 WIFI Shield
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Personal
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
- 32-bit RISC architecture
- The processor can operate at 80MHz / 160MHz
- 32MB flash memory
- 64kB for instructions
- 96kB for data
- Operates in AP, Station or AP + Station mode
- It has 11 digital pins
- It has 1 analogue pin with 10-bit resolution
- Digital pins except the D0 have interrupts, PWM, I2C and one wire
- Programmable through USB or WiFi (OTA)
- Compatible with Arduino IDE
- Compatible with modules and sensors used in Arduino
Ultrasonic Module Waterproof
- Operating Voltage: 5 V
- Sonar Sensing Range: 25-450 cm
- Sensing Range: 450 cm
- Frequency: 40 kHz
- Resolution: about 0.5cm
- Quiescent current: 5mA
- Total current draw: 30mA
- Beam Angle: less than 50 degrees
- Working temperature: -10 ~ 70 Celsuis
- Storage temperature: -20 ~ 80 Celsuis
- Small size, easy to use
- Low voltage, low power consumption
- High accuracy
- Strong anti-jamming
- Integrated with wire enclosed waterproof probe
- Suitable for wet, harsh measurement
12 V 10W Solar Panel
- Output Power: 10 Watts
- Operating Voltage: 12 Volt
- Panel Technology: Poly Crystalline
- Performance Warranty:25 Years
- Wattage (Wp): 20
- Voltage at Max Power: 16.25 volts
- Current at Max Power: 0.59 amps
- Open Circuit Voltage: 20.9volts
- Short Circuit Current: 0.65A
- of cells: 36
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- A+ Grade, anti PID Poly Crystalline cell
- Cell Conversion efficiency > 16%
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Dimensions: 285 x 350 x 22mm
- Weight: 2.5 Kg
NEMA 17 1.6 kgcm
- Operating Voltage : 12~16 V
- Step Angle : 1.8°
- Holding Torque : 1.6 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :0.31 Ampere
- Number of Leads : 6
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Metal mechanical Arm Gripper claw
- Metal Gripper Robotic Arm
- Operating Voltage: 4.8V to 6.6V
- Material: Aluminum Alloy
- The Kit comes with hardware, unassembly
- Clamp Max open: 55mm
- Clamp total length:108mm
- Clamp total width:98mm (when the Clamp open
- Light weight plank kit
- Compatible with HS322, HS422, MG995, SG5010 servo
- Degree of Freedom (DOF): 2
- Bearing Type: Ball Bearing
- Weight: About 68g
7 mm 6 LED Endoscope Waterproof Inspection Borescope Camera 5M USB Cable
- Lens Diameter: 7.0MM
- Pixel: 0.3 megapixels
- Resolution: 640*480
- sensor size: 1/9 inch
- Frame Rate: 30fps
- View Angle: 67 degree
- Focal Distance: 3cm-10cm-
- LED Lights: 6pcs
- Interface: USB2.0
- Photo format: jpeg
- Video Format: AVI
- Waterproof level: IP67
- Support Computer: Windows XP/7/8/10/Mac
- Cable Length: 5M
- operating temperature: 0 degrees to 70 degree
- Dimension: Approx. 13.5*13.5*3cm
- Weight: 52g
Water flow sensor SEN-HZG1WA Pulse Output 4~45L/min Liquid Switch Flowmeter
- Model: SEN-HZG1WA.
- Use voltage: DC 5V.
- Connect way: G1”, 60*34*34(mm).
- Working voltage range: DC 4.5 ~18V.
- Working current: 15mA.
- Test range: 4~45L/min (m³/h).
- Fit media: water.
- Working pressure: 1.75MPa.
- Outside nominal diameter: G1 (mm).
- Instantaneous flow pulse characteristics: F= [5Q-3]±10%, F means instantaneous pulse value(Hz),Q means instant flow(L/min).
- Insulation resistance = 100MO.
- Electric strength: AC 500V, 50Hz.
- Precision grade: +-10%.
- Working temperature: 60 degree C
- Type: vane-wheel type flowmeter.
MPU-9250 GY-9250 9-Axis Sensor Module I2C/SPI Communications
- Acceleration, Gyroscope, and Magnetometer
- Power Supply: DC3.3V-5V
- Chip: MPU9250
- Gyro range : ± 250 500 1000 2000 ° / s
- Acceleration range: ± 2 ± 4 ± 8 ± 16g
- Magnetic field range: ± 4800uT
- Pin spacing: 2.54mm.
- 9 DOF modules
- Build-in ultra-low noise linear LDO voltage regulator.
- Built-in onboard filters, which reduce noise from the motor and other high current electronics.
- All sensors are connected to the I2C bus.
- Build-in the Logic level converter for I2C.
- Power indicator LED.
- Using Immersion Gold PCB, machine welding process to ensure quality.
- On-board pull-up resistors on SDA, SCL, and nCS
- On-board pull-down resistors on FSYNC and Ado
- Size: 22 mm x 17 mm.
JF-0630B DC 24 V 300mA 10mm 6N Push Pull Solenoid Electromagnet
- Model: JF-0630B
- Rated Voltage: DC 24V
- Type: Pull Push
- Rated Current: 300mA
- Force & Stroke: 6N/10mm
- Body Size: 30 x 20 x 18mm
- Plunger Bar Size : 7 x 58mm
- Mounting Hole Diameter: 2.5mm
- Cable Length: 19cm
- Weight: 46g
- Iron Body Material
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction tightly sucks the iron, thus locking the door.
- Designed with the open frame type and mount board, high power.
- being installed in the escape door or fire door electronic controlled system.
- Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong
Arduino Duemilanove Development Board with USB Cable
- Microcontroller: ATmega168/ATmega 328
- Operating Voltage: 5V
- Input Voltage: 7-12V
- Input Voltage: 6-20V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by the bootloader
- SRAM: 1 KB (ATmega168) or 2 KB (ATmega328)
- EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328)
- Clock Speed: 16 MHz
