Leap Motion Controller
- Power supply: 5V DC via USB connector (minimum 0.5A)
- Data connection: USB 2.0
- Interaction zone: Depth of up to 60cm (24”) preferred, up to 80cm (31”) maximum;
- 140×120° typical field of view.
- 3 LEDs spaced on either side and between the cameras, baffled to prevent overlaps.
- Construction: Aluminium and scratch-resistant glass
- Operating temperature: 32º to 113º F (0º to 45ºC)
- Storage temperature: 14º to 122º F (-10º to 50º C)
- Relative Humidity: 5% to 85% (non-condensing)
- Two 640x240-pixel near-infrared cameras; spaced 40 millimetres apart infrared-transparent window, operate in the 850 nanometre +/-25 spectral range; typically operates at 120Hz; capable of image capture within 1/2000th of a second.
- Highly accurate hand and finger tracking with near-zero latency
- 135° field of view extending above the device
- Orion SDK compatible with Windows 7 or newer
- Updated V4 tracking
OpAmp Breakout – LMV358
Single Beam 15 m Photoelectric Active Infrared Intrude Detector IR Sensor Tamper Alarm
- Working Voltage: 12V, 24V
- Working Current: 50MA
- Infrared Frequency: 1.92khz
- Wavelength:940nm
- With rain-proof design
- Operating temperature: --20 degrees to 50degrees
- Relay output : 1 a max *36 v
- Response time(Relay output) <10 ms,
- Hold time(Relay output) 300ms
- Range can be reduced to 30% in bad weather conditions: for rain , dust , etc
- Unique digital filter circuit design, strong anti false alarm ability
- With high levels of anti-RFI/EMI capability
- Fully sealed design, rain-proof(fog),dust-proof(worm),suitable for hostile environment
- Used with kinds of alarm panel and access control system.
- Detector Range: indoor 20m. Outdoor 10m, Detection mode Presence(beam interruption)
- Size : 49.2 x 76 x 21.6MM,
DHT21 AM2301 Digital Temperature Humidity Sensor module SHT11 SHT15 Arduino
- Power: DC 3.3-5.2V
- Humidity: 0~99.9% RH
- Temperature: -20 ~ 60℃
- Precision: ±3% RH, ±0.5 ℃
- Output: Digital (1 wire)
- Accurate, durable and high quality
- 4 pin package
- Ultra-low power
- No additional components
- Excellent long-term stability
- All calibration, digital output
- Completely interchangeable
- Long distance signal transmission
- Relative humidity and temperature measurement
- Dimension: 60 x 27 x 14mm
HR202 Digital Temperature Humidity Sensor
- Working Voltage: 3.3 V-5 V
- Output AO - analog output, DO - digital output
- High-quality HR202 humidity sensor
- Comparator output signal is clean, good waveform, driving ability, more than 15mA
- Adjust the temperature distribution position detection threshold
- The output form: DO digital switching outputs ( 0 and 1 ) and AO analog voltage output
- A fixed bolt holes for easy installation
- Using a wide voltage LM393 comparator
- PCB Board Size: 3.2 cm x 1.4 cm
HCZ-H8-B Humidity Sensor, HCZ Series, 20% to 90% RH, 3 %, Through Hole, No Housing
STA 540 Audio Amplifier
- High output power capability
- Minimum external components count:
- Standby function (CMOS compatible)
- No audible pop during standby operations
- Diagnostic facilities:
- Protection
Voice Module Sound Module Audio Player WT588D
- Input Supply voltage (V) :2.8 ~ 5.5
- Current consumption (sleep mode: 10 µA
- Sampling frequency (kHz): 6 ~
- Built 13Bit/DA converter, and 12Bit/PWM output.
- Support for loading WAV audio formats
- Module package (with FLASH memory and peripheral circuits) have DIP16, DIP28, chip packaging has DIP18, SSOP20, and LQFP32 form
- Built 13Bit/DA converter, and 12Bit/PWM output
- PWM output can directly drive 0.5W/8Ω speakers, push-pull current abundant support DAC / PWM output of two ways;
- Support for loading WAV audio formats;
- USB download mode, support for online download / offline download; WT588D voice chip, even in the case of electricity, will also be able to download the data to the normal SPI-Flash;
- Supports MP3 control mode, control mode button, 3 × 8 key combination control mode, parallel control mode, front-line serial control mode, three-wire serial control mode, and three-wire serial control I / O port expansion output mode;
- Support load 6K ~ 22KHz audio sampling rate
- Up to 500 segments can be loaded for editing audio
Text to Speech TTL Module (Serial to Speech)
- Single row 0.1″ header for easy connection to a host system
- Power requirements: +5 VDC
- 30 mA idle
- 46-220 mA active (depending on speech parameters and output load)
- Communication: Asynchronous 9600 bps serial (8N1)
- Dimensions: 1.25″x1.5″x0.37″
-
Text support rate is better
-
Interface operation is simpler
-
5V single power supply.
-
Output directly connected to the speaker, can drive 4 ohms 3W / 8 ohm 2W speakers
-
Busy status output, can be connected to the microcontroller IO or indicator light, no need to be left floating.
-
Voice effect optimization
-
Module miniaturization and easy integration
-
Dimension: 33*27.5mm
-
With mounting holes
Speech Recognition Module
- Working voltage: 3.3/5V
- Local Voice Recognition
- Very low rate of false triggering
- Speaker connector(JST2.0, the speaker is not included)
- Built-in microphone
- 22 recognition entry
- Default Baud rate: 9600
- Flash: 2Mbytes
- Microphone Sensitivity: -40dB
- Microphone SNR: 58dB
- Operating temperature: 0 – 85 degrees C
Fingerprint Scanner TTL GT511C3 – 3.3V to 6V
- Model: GT-511C3
- Operating Voltage(VDC): 3 to 6
- CPU: ARM Cortex M3 Core (Holtek HT 32F2755)
- Sensors: Optical
- Image Size: 202 x 258 Pixel
- Resolution: 450 DPi
- Effective Scanning Area(mm): 20 x 16
- False Acceptance Rate (FAR): 0.001%
- False Rejection Rate(FRR): < 0.1%
- Operating Temperature : -20°C ~ +60°C
- Default Baud Rate: 9600bps
- High-Speed, High-Accuracy Fingerprint Identification using the Smack Finger 3.0 Algorithm
- Read and Write Fingerprint Templates and Databases
- Simple UART protocol (Default 9600 baud)
- Capable of 1:1 Verification and 1:N Identification
- High-accuracy & high-speed fingerprint identification technology.
- Works well with dry, moist, or rough fingerprints.
- 200 fingerprints storage.
- Easy one-touch enrolment.
- Dimensions(mm): 37 x 17 x 9.5
- Weight: 6gm