HSS DRILL BIT SET
9*15cm PERFBOARD
7*9cm PERFBOARD
PCB 12*18 cm
PCB 2*3 inch
RIBBON CABLE
MOQ : 1 m
- Rate temperature: 105°C
- Rated voltage: 300V
- Average tensile strength: 1500 lbs
- Spark test: 2500V
- Dielectric strength test: Minimum 2 KV in 1 minute
- Conductor resistance: Maximum 237Ω/km
- Insulation resistance: Minimum 100 MΩ-km
- Capacity: 44pF/m (G-S-G)
- Inductance: 1.45μH/m
- Characteristic Impedance: 105Ω (G-S-G)
- Propagation delay time: 4.2 ns/m
- Â Durable and reusable
- Easy to install and use
- A popular choice for construction or repair
- Useful for the electronic project and Genuine Arduino product
XL4015 5A STEP DOWN WITH HEAT SINK
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 degree + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- Power indicator
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL4015 5A STEP DOWN WITH DISPLAY
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 degree to + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- LED to indicate power status
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
XL6009 4A DC to DC BOOST CONVERTER
- Module Properties: Non-isolated boost (BOOST)
- Rectification: Non-Synchronous Rectification
- Input Voltage Range: 3V ~ 32V
- Output Voltage Range: 5V ~ 35V
- Input Current: 4A (max), no-load 18mA
- Conversion efficiency: <94%
- Switching frequency: 400KHz
- Output Ripple: 50mV (the higher the voltage, the greater the current, the greater the ripple)
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 0.5%
- Operating Temperature: -40degree ~ +85 degree
- Dimensions: 43mm * 21mm * 14mm
XL4015 5A STEP DOWN MODULE
- Module nature: non-isolated buck module ( BUCK )
- Input voltage: 4-38V
- Output voltage: 1.25-36V
- Output current: 0-5A, it is recommended to use within 4.5A
- 14 Digital I/O Pins
- Output power: It is recommended to use within 75W, please add a heat sink if it exceeds 50W
- Working temperature: -40 ~ + 85 degrees
- Working frequency: 180KHz
- Conversion efficiency: up to 96% Load adjustment rate: S ( I ) ≤ 0.8%
- Voltage adjustment rate: S ( u ) ≤ 0.8%
- Power indicator: No
- Short circuit protection
- Over-temperature protection
- Dimension: 54mm * 23mm wide *18mm
WS2812 LED BREAKOUT BOARD
- Input Voltage: -0.5～VDD+0.5V
- Supply voltage: 5v
- Operating voltage: 4v -7v
- Integrating control circuit and RGB chip
- Built-in signal reshaping circuit
- Built-in electric reset circuit and power lost reset circuit
- 256 brightness and 16777216 colour display
- Viewing angle: 120 degree
- Cascading port transmission signal
- Red Vf: 1.8~2.2V
- Green Vf: 3.0~3.2v
- Blue Vf: 3.2~3.4V
- Red Wavelength: 620~630 nm
- Green Wavelength: 515~530 nm
- Blue Wavelength: 465~475 nm
- Red luminous intensity(20mA): 550~700mcd
- Green luminous intensity(20mA): 1100~1400mcd
- Blue luminous intensity(20mA): 200~400mcd
- Dimension: 1.8*1.3*0.8mm
