PIR Motion Sensor Concealed LED Light Connect Upto 500W (Natural White)
 PIR Motion Sensor with Concealed LED Light is a lighting device that combines a motion sensor and an LED light. Here are some details about this product:
- Function: The PIR Motion Sensor is designed to detect motion in its vicinity and automatically turn on the concealed LED light when motion is detected. It is commonly used as a security feature or for convenience in areas such as hallways, staircases, or outdoor spaces.
- Motion Sensor: The PIR (Passive Infrared) motion sensor detects changes in infrared radiation emitted by objects in its detection range. When it senses motion, it sends a signal to the LED light, triggering it to turn on. This helps to conserve energy by only activating the light when needed.
- LED Light: The PIR Motion Sensor features a concealed LED light with a power rating of 7 watts. The LED technology offers energy efficiency, longevity, and good illumination.
24VDC OMRON 8 CHANNEL INDUSTRIAL QUALITY RELAY MODULE CARD
The OMRON RELAY G2RL1 12AMP AUTORICH Relay Card has 1 C/O, 8 channels, and operates at 24V DC, making it suitable for industrial applications. -Switching current up to 12A at 230 VAC (or 30 VDC) - Low Coil Drive Current (4.7 mA to 100 mA) -Easy to replace pluggable relays. -The possibility of bussing (jumping) relays in a shared negative and positive configuration. -Freewheeling diode across the relay coil. -Mounting options include DIN rail mounting and panel mounting.
Digital Energy Meter Power Meter 100A
- Working voltage: 80 ~ 260VAC
- Test voltage: 80 ~ 260VAC
- Current:100A
- Rated power: 100A/22000W
- Operating frequency: 45-65Hz
- Measurement accuracy: 1.0 grade
- Size: 9*5*2.5cm/3.5*2*1in
- Wire length:19cm/7.5in
- It can display voltage, current, power, power factor, energy, and frequency at the same time.
- Backlight control, short press to turn on/off the backlight.
- The energy can be reset using the key.
LCR METER MODULE
Electricity Failure Alarm
STEPPER MOTOR NEMA 23 7.2KG
24V/12V to 5V 5A Power Module DC-DC XY-3606 Power Converter
- Working voltage: DC 9V–36V
- Output voltage: 5.2V/5A/25W
- 9~24V input: Output 5.2V/6A/30W
- 24~32V input: output 5.2V/5A/25W
- 32~36V input: output 5.2V/3.5A/18
- The synchronous rectification scheme, wide voltage, high current, high efficiency.
- With DC plug and terminals, easy to use.
- With USB port, fast-charge identification chip compatible with Android and iPhone mobile phones.
WeMos D1 ESP Wroom 02 Board ESP8266 Mini WiFi Nodemcu Module 18650 Battery
- One AD inputs.
- Micro USB inputs.
- One programmable LED (D0).
- AUTO PROGRAM circuit.
- ESP8266 (ESP-WROOM-02 With TELEC) is equivalent to the NodeMCU.
- Analog Input (AD): Built-in dividing resistor (AD = 220K ADC 100K = GND).
- There is a SOLDER terminal for SLEEP MODE.
- Compatible With Arduino andNodeMCU.
- Operation and charging are possible at the same time.
- 18650 charging circuit including the 5V boosting circuit with TP5410.
- Overcharge protection, over-discharge protection built-in.
- LED: Red = Charging, Green = Full charging.
- 3000 mA 18650 It is possible to operate for more than 17 hours on a battery.
- Integrated 18650 battery charging and discharging system.
- One switch controls whether the 18650 battery is on power or not.
- OLEDs SDA and SCL can connect to the D1 pin and the D2 pin respectively.
- The five buttons can be controlled by FLATH, RSET, D5, D6, and D7 respectively.
- The 5 Digital pins can configure the write/read/interrupt/PWM/I2C/one-wire supported separately.
- Operation and NodeMCU consistent, adding a programmable LED, you can use GPIO16 to control; display 8266 running status and other functions. Integrated OLED and five buttons, more convenient for development.
- The design concept originates from the open-source project NodeMCU; the development board integrates 18650 charging and discharging systems with charging and discharging protection. At the same time, an OLED and five directional buttons are integrated to facilitate the development.
