XR2206 High Precision Function Signal Generator
- Voltage Supply: 9-12V DC Input.
- Waveforms: Square, Sine & Triangle.
- Impedance: 600 Ohm + 10%.
- Frequency: 1Hz-1MHz.
- SINE WAVE.
- SQUARE WAVE.
- TRIANGLE WAVE.
- High resolution, can generate sine/triangle/square waveforms.
- Adjustable frequency and amplitude.
- Frequency adjustment features coarse tuning and fine-tuning.
- All are through-hole components, easy for installation.
- Dimension: Approx. 12 * 8 * 2cm
- Weight: 69g
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process:
- Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
- Internal pull-down resistors on inputs: 100 kΩ
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
6 inch Thermostat
Product Description
A thermostat functions as a temperature-activated switch, energizing heating elements when the water temperature falls below its set point. It regulates the temperature of a water heater by switching the heating element on and off, acting as a safety device to prevent scalding and malfunctions. A104196
4S46B0 Rotary Cam Switch
Product Description
Current : 10 A Rotary cam switches are hand-operated mechanical switching devices used for controlling electrical circuits in various applications. They function by rotating a shaft, which in turn opens or closes contacts to make or break electrical connections. These switches are often used for on/off switching, isolating power to specific areas, controlling motors, and switching auxiliary circuits. A103813
PLC Basic Terminal Block
Microwave Motion Sensor
Product description
The microwave sensors is working according to the microwave Doppler effect , it can be widely used in as automatic control switch, the security system, and Automatic video control system of ATM, as well as other automatic induction control area.
The Detection way has the below advantages compared with other as follows:
1. Non-contact Detection,
2. Suitable for bad environment, immune to temperature, humidity, noise, air, dust, Light.
3. RF interference ability.
12V Gear Motor High Torque Electric Micro Speed Reduction Geared Motor
Micro Switches
Microwave Sensor
1.3″ OLED Display I2C 128*64 display module Blue 4pin
1.8″ TFT DISPLAY FOR ARDUINO
- Display Size: 1.8″
- Driver IC: ST7735
- Input Voltage (V): 3.3 to 5
- Pixel Resolution: 128 x 160
- Interface Type: SPI
- 18-bit (262,144) colour
- 4 or 5 wire SPI digital interface
- Built-in microSD slot – uses 2 more digital lines5V compatible!
- Use with 3.3V or 5V logic
- On-board 3.3V @ 150mA LDO regulator
- 2 white LED backlight, a transistor connected so you can PWM dim the backlight
- 1×10 header for easy breadboarding
- 4 x 0.9″/2mm mounting holes in corners
- Overall dimensions: 34 x 56 x 6.5mm
- Current draw is based on LED backlight usage: with full backlight draw is ~50mA