40N60 Field Stop IGBT 600V 40A
LM1876 Dual 20W Audio Power Amplifier IC
- Dual 20W Audio Power Amplifier with Mute and Standby Modes
- Spike Protection
- Minimal amount of external components necessary
- Quiet fade-in/out mute mode
- Standby-mode
- Isolated 15-lead TO-220 package
- THD+N at 1 kHz at 2 x 15W continuous average output power into 4Ω or 8Ω: 0.1% (max)
- THD+N at 1 kHz at continuous average output power of 2 x 20W into 8Ω: 0.009% (typ.)
- Standby current: 4.2 mA (typ.)
PIC16F873A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 7 kB
- RAM: 192 byte
- Internal Oscillator: No
- ADC: 1 (5 channels)
- of Pins: 28
- Voltage: 2V - 5.5V
- 100,000 erase/write cycle Enhanced Flash program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory typical
- Data EEPROM Retention > 40 years
- Self-reprogrammable under software control
- In-Circuit Serial Programming™ (ICSP™) via two pins
- Single-supply 5V In-Circuit Serial Programming
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving Sleep mode
- Selectable oscillator options
- In-Circuit Debug (ICD) via two pins
- Low-power, high-speed Flash/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Commercial and Industrial temperature ranges
- Low-power consumption
4 Channel 5V Relay Module Shield For Arduino
- Product Type: 4-Channel relay module
- Dimensions: 75 mm x 55 mm x 19.3 mm
- Weight: 61 g
- Relay colour: Blue
- PCB colour: Blue
- Maximum output of relay: AC250V 10A and Dc30V 10A
- Number of Relays: 4
- Control signal type: TTL level
- Input voltage: 5v
- Compatible with: Arduino, AVR, PIC, ARM, Raspberry Pi etc
- Package contains: 1 piece of 4 channel relay module
NANO / UNO Multi-Purpose Expansion Board
- The Sensor Shield makes your connections with the Arduino Nano much easier
- It is compatible with Arduino Nano 2.0 and 3.0
- The shield has up to 8 analogue pins, 13 digital I/O pins, and Aref with 3 pin connectors (GND, Vcc, Signal).
- Consists of an independent I2C port with 4pins (SDA, SCL, GND, and Vcc) and UART (Rx, Tx, Vcc, and GND).
- Reset button onboard and a female jack for external power supply
- Material: FR-4 Epoxy Glass Fibre Board
- IO port leads all digital and analogue IO ports, each IO port has positive and negative power supply interface standards.
- Leads to an I2C interface on the motherboard, convenient and I2C devices connected.
- Size: Approx. 57x53x8mm
12V DC Geared Motor 2000 RPM
L293D Motor Driver Shield
- L293D motor driver chip & 74HC595 shift register
- Four H-bridges
- Terminal blocks and jumper to connect external power, for separate logic/motor supplies
- Up to 4 bi-directional DC motors with individual 8-bit speed selection
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
- PCB Size: 69 x 53 mm
Aluminum Metal Servo Arm 25T Metal Horns Round Type Disc
Magnetic Door Open Sensor – N/C Type
- Max Voltage: 100V DC
- Max Rated power: 10W
- Sensing Distance: 15-25mm
- Wire lead: 24 Awg, about 350mm long
- Rated Current: 100mA
- Connecting mode: N.C. (Normally closed)
- Easy to install
- Strong concealment
- Magnetic sensor alarm, control the switch of the circuit via the built-in magnet
- Alarm when someone intrudes into your places
- Can be used in places like apartments, hotels, offices, etc.
- Ideal for residential or commercial use.
- Designed to do embedded in the door or window frame.
- Dimension: approx. 27 x 14 x 8mm
L298N MOTOR DRIVER
- Driver model: L298N 2A
- Driver chip: Double H bridge L298N
- Motor supply voltage: 46V(maximum)
- Motor supply current: 2A(maximum)
- Logic voltage: 5v
- Driver voltage: 5V-35V
- Driver current: 2A
- Logical current: 0-36mA
- Maximum power: 25W
- Current sensor for each motor
- LED indication for power status
- Heat sink for better performance
- Operating temperature: -25 degrees to 135 degrees Celsius
- Can be interfaced with simple manual switches, TTL logic gates, relays, etc.
- Dimension: 55*60*30mm
- Weight: 33gm
16*2 WHITE (LCD DISPLAY MODULE)
- Input voltage: 4.7V TO 5.3V
- Operating voltage: 5V
- View angle: 6 o clock
- Current supply:1.1
- Maximum supply current:2.5
- 1/16 duty cycle
- Input leakage current:1micro ampere
- Chip on board IC
- Rise time:200 to 250ms
- Fall time: 300 to 350ms
- Controller: SPLC780D
- Each character build by 5*8 pixels
- Consist of 2 rows with each row has 16 characters
- Works on both 8 bit and 4 bit
- Operating temperature:0 degree to 50 degree Celsius
- Storage temperature: -10 degrees to 50 degree Celsius
- Low Current consumption
- Alphanumeric display
- Dimension: 69.5*14.5mm
- Compact size and lightweight
- Easy to interface
