TowerPro SG92R Mini Micro Servo 9g 2.5kg
- Operating Voltage: 4.8V to 6.0V
- Operating Temperature Range: -10 to +60 Degree C
- Operating Speed (4.8V): 0.12sec/60 degrees at no load
- Operating Speed (6.0V): 0.10sec/60 degrees at no load
- Stall Torque (4.8V): 1.8kg/cm
- Stall Torque (6.0V): 2.4kg/cm
- 360 Modifiable: Yes
- Bearing Type: Ball Bearing
- Gear Type: Nylon Gears
- Connector Wire Length: 12"
- Pulse Width: 500-2400 µs
- Rotation Angle: 180 degree
- Dimension: 21.5 x 11.8 x 22.7mm
- Weight: 9g
PIC16F877A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 14 kB
- RAM: 368 byte
- Internal Oscillator: No
- ADC: 1 (8 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- 100,000 erase/write cycle Enhanced Flash program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory typical
- Data EEPROM Retention > 40 years
- Self-reprogrammable under software control
- In-Circuit Serial Programming™ (ICSP™) via two pins
- Single-supply 5V In-Circuit Serial Programming
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving Sleep mode
- Selectable oscillator options
- In-Circuit Debug (ICD) via two pins
- Low-power, high-speed Flash/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Commercial and Industrial temperature ranges
- Low-power consumption
5-36v Switch Drive High-power MOSFET Trigger Module
- Operating Voltage: DC 5V - 36V;
- The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support.
- Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
- Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
- PWM, motor speed control, lamp brightness.
- Availability: unlimited switch
- Operating temperature: -40-85
- Dimension: 34mm x 17mm x 12mm
- The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
- Wide voltage, the perfect support for PWM
- Easily control high power devices
- Input PWM to achieve motor speed control, lamp brightness control
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
DC 12V Pneumatic Diaphragm Water Pump Motor R365
- Model: R365 DC micro diaphragm pump
- Working voltage: DC 12V
- No load current: 0.23A
- Maximum flow: 2-3 liters/minute
- Outlet maximum pressure: 1-2.5 kg
- Maximum lift: 1-2.5 meters
- Maximum suction: 2 meters
- Motor length: 32mm
- Motor diameter: 28mm
- Pump length: 36mm
- Total length: 69mm
- Pump diameter: 40mm x 35mm
- Weight: 111 g Approx
6 PIN 128*64 OLED 0.96” WHITE
- Super high brightness
- Super high contrast
- Visual angle>160
- Input voltage: 3.3V to 6V
- Compatible I/O level:3.3v, 5v
- Communication mode: SPI, only need 2 I/O port to control
- Driver IC: SSD1306
- Module volume:27*27*4.1mm
- Working temperature: -40 degree to 70 degree
- Full compatible with Arduino
- Configured for SPI protocol and can be easily changed to IIC
- Weight: 7gm
6 PIN 128*64 OLED 0.96” BLUE-YELLOW
- Resolution: 128*64
- Driver IC: SSD1306
- Visual angle>160
- Input voltage: 3.3V to 5V
- Power: 0.04W
- Pixel color: Yellow(16 Rows) and Blue
- No backlight, OLED self light
- Communication via I2C
- Works with ESP8266, Arduino, Raspberry Pi, 8051, MSP420, STM32
- Module volume: 27*27*4.1mm
- Working temperature: -30 degree to 80 degree
- Configured for SPI protocol and can be easily changed to IIC
4 PIN 128*64 OLED 0.96” BLUE
- Super high brightness and high contrast
- Driver IC: SSD1306
- Input voltage: .3v to 6 v
- Ultra-wide viewing angle >160 degree
- Low power consumption with 0.04 W
- Support wide range of Voltage: 3.3V to 5V
- OLED self-lights, no backlight required
- Fully compatible with Arduino
- Communication via IIC, only two I/O ports
- Working temperature: -30 degree to 80 degree
- Dimension: 27*27*4.1mm
- Supported platform: Arduino, 51 series, MSP430, SCR chips
- No font is required, software takes the word MODULO
Solar Panel 6V 200mA
- Polycrystalline solar cell
- Max output power: 1.1W
- Max working voltage: 6.6V
- Max charging current: 110mA
- Min output power: 0.6W
- Min working voltage: 6V
- Min charging current:200mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Laser cut to proper size and encapsulated in special sun and weather resistant materials;
- Weight 33 Gms
12v 200mA Solar panel
- Output voltage：12V
- Output current: 200mA
- Service life: more than 5 years
- High transfer efficiency
- Non-pollution and reproducible
- 2.4-watt polycrystalline solar panel
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape
- Size: 213 x 92mm
- Weight：70g
MEGA32A Atmel Microcontroller IC
- Flash (Kbytes): 32 Kbytes
- Pin Count: 44
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 32
- Ext Interrupts: 3
- SPI: 1
- UART: 1
- ADC channels: 8
- SRAM (Kbytes): 2
- EEPROM (Bytes): 1024
- Operating Voltage (Vcc): 2.7 to 5.5V
- Package: PDIP 40P6 40High-performance, Low-power Atmel®AVR® 8-bit Microcontroller
- Advanced RISC Architecture
- High Endurance Non-volatile Memory segments
- Peripheral Features includes Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes , One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode , Real Time Counter with Separate Oscillator , Four PWM Channels ,8-channel, 10-bit ADC.
- Special Microcontroller Features includes Power-on Reset and Programmable Brown-out Detection , Internal Calibrated RC Oscillator
- Operating Voltages – 2.7V - 5.5V for ATmega32L ,4.5V - 5.5V for ATmega32
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm