Stepper Motor NEMA 34 68 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Holding Torque: 68 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
Sunny Sky A2212 980 kv
- Poor man’s Tiger motor
- Brand name: Sunnysky
- KV: 980KV.
- Framework: 12N14P
- Operating Current: 6A ~ 18A
- Peak Current: 14A
- Shaft: 3mm.
- thrust: 880g
- Stator Diameter: 22mm
- Stator Thickness: 12mm
- of Stator Slots: 12
- of Rotor Poles: 14
- Motor Resistance: 123mΩ
- Max Continuous Power: 330W
- Recommended Lipo Batteries: 2-3S
- Recommended Propeller: 9-10
- Recommended Esc between 25A and 30A are
- High-quality bearings for reliable operation.
- Imported silicon steel coils, and high-quality magnets ensuring longer life and better performance.
- Generates less heat during operations.
- Suitable for RC Airplane or Multi rotor helicopter
- Dimension: 27*30mm
- Weight: 50gm
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process:
- Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
- Internal pull-down resistors on inputs: 100 kΩ
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
TB6612FNG Dual Motor Driver Module 1A for Arduino/Other Microcontroller
- Driver Model: TB6612FNG
- Operating voltage: 2.7 V to 5.5 V
- Limited Maximum Voltage: 15V max
- Output current: 1.2A
- Maximum Current: 3.2A (peak)
- Number of Channels: 1
- Standby control to save power
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1 spaced pins
- Filtering capacitors on both supply lines
- Dimensions: 30 x 20 x 10mm
- Weight: 22 gm
TowerPro SG90 Mini Servo – 180 degree Rotation
-
- Model: SG90
- Operating voltage: 3.0V- 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 1.2kg-cm
- Stall torque @6.6V : 1.6kg-cm
- Torque: 2.5kg/cm
- Operating speed is 0.1s/60°
- Gear Type: Plastic
- Rotation : 0°-180°
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
- Weight: 9 gm
ULN2003 Driver
- Contains 7 high-voltage and high current Darlington pairs
- Each pair is rated for 50V and 500mA
- Input pins can be triggered by +5V
- All seven Output pins can be connected to gather to drive loads up to (7×500mA) ~3.5A.
- Can be directly controlled by logic devices like Digital Gates PIC etc
- Available in 16-pin DIP, TSSOP, SOIC packages
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
UNITE DC 48V 750W BM1418ZXF Brushless Gear Motor
VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver
- Driver Model: Monster Moto Shield VNH2SP30
- Operating Voltage: 12V to 16V DC
- Maximum current rating: 30 A
- Continuous Current: 14 A
- Number of Channels: 1
- MOSFET on-resistance: 19 m (per leg)
- Maximum PWM frequency: 20 kHz
- Current sensing available to Arduino analog pin
- Thermal Shutdown
- Under voltage and Overvoltage shutdown.
- Dimensions: 55 x 28 x 12mm
- Weight: 15gm
XB NEMA 23 (57mm) Coupling 6.35x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 8mm
- Small Bore Diameter: 6.35mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 6.35mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.
XB NEMA 34 (86mm) Coupling 12.7×12.7mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Bore Diameter: 12.7*12.7mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.