- You cannot add "3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM" to the cart because the product is out of stock.
3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM
- MAVLink protocol framing status documents.
- Frequency modulation and Spread Spectrum (FHSS).
- Self-adaption to time-division multiplexing.
- Support LBT and AFA.
- Configurable duty cycle.
- Built-in error correcting code(up to 25% data bit error).
- AT command configures data transmission.
- RT command remote control data transmission.
- Interchangeable air and ground 433MHz modules.
- Micro-USB port.
- 6-position Molex connector.
- 250mW maximum output power (adjustable).
- SMA connector.
- 2-way full-duplex communication through adaptive TDM.
- UART interface.
- Transparent serial link.
- Open-source SIK firmware.
- Configurable through *Mission Planner and *APM Planner.
- Featuring a SiLabs Si1000 RF Microcontroller
- Support OTG of Android Cellphone and Compute
- Based on the Hope RF HM-TRP radio Module,
433mHz Transmitter Receiver RF Radio Module
- Range in open space(Standard Conditions) : 100 Meters
- RX Receiver Frequency: 433 MHz
- RX Typical Sensitivity: 105 Dbm
- RX Supply Current: 3.5 mA
- RX IF Frequency: 1MHz
- RX Operating Voltage: 5V
- TX Frequency Range: 433.92 MHz
- TX Supply Voltage: 3V ~ 6V
- TX Output Power: 4 ~ 12 Dbm
- Low Power Consumption
- Easy For RF-based Application
- Complete Radio Transmitter
- Transmit Range Up To 50m
- CMOS / TTL Input
- No Adjustable Components
- Very Stable Operating Frequency
- Low Current Consumption (Typ 11mA)
- Wide Operating Voltage
- ASK Modulation
434MHz/315Mz TX & RX
Transmitter
- Working voltage: 3V - 12V for max. power use 12V
- Working current: max Less than 40mA max , and min 9mA
- Modulation mode: ASK
- Working frequency: 433MHz
- Transmission power: 25mW
Receiver
- Working voltage: 5.0VDC
- Working current:≤5.5mA max
- Modulation method: OOK/ASK
- Working frequency: 433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel –100dBm (50Ω)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]
- Operating voltage: 3.6~5.5v ( 5v recommended),
- Receiver sensitivity as high as -110dbm,
- Compatible with HT12E and HT12D,
- Low power and good range.
- High-frequency stability and low coherence and interference
- Easy interfacing with the RF modules, using the female headers for placing the modules.
- Breakout pins for connecting to the microcontroller.
- DIP Switch for Address Selection (when multiple modules are used at one location)
- Status LED for valid transmit.
- Supports both ASK, FSK RF modules
- Small size, high quality PCB.
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4