1 meter 7 x 7 mm Cable drag Chain Wire Carrier With End Fits
Arduino CNC Shield
- Shield type:Â Arduino Nano
- Firmware:Â GRBL
- Modular stepper motor drivers:Â 3
- Limit switches:Â 6
- Micro-stepping:Â 1/16
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.51
Arduino CNC Shield v3 Engraving Machine/3D Printer/A4988 driver GRBL compatible
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin Molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
CNC Shield V4 for Engraving Machine 3D Printers Controller Board
- Worked with Arduino nano.
- 3 axis stepper motor driver
- Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine.
- 2A can be controlled within the two-phase four-wire stepper motor.
- Released the digital IO interface, easy to connect to other modules, such as ENDSTOP.
- Released the I2C interface, you can connect to the LCD I2C or another I2C module.
- Power DC5V interface, 7.5-12V voltage input.
- GRBL compatible
GT2 Open Timing Belt for 3D Printer and CNC
MOQ: 1 m
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 10M
- Shape: Open Loop
- Core Wire Material: Glass Fiber
- Precision registration and timing with no loss of high torque carrying capability
- Minimal vibration and chordal effect
- Positive slip proof engagement
- Wide speed range, especially important when the entire speed range is developed from a single source
- Virtually no elongation (stretching) due to wear
- Power transmission efficiency is not lost with the use
- A clean operation, no need for lubrication
- Reduced noise.
- Long, dependable trouble-free service.
Lead Copper Nut 8mm
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
Nema17 Stepper Motor With Stainless Steel 8mm 300mm Lead Screw + T8 Nut For 3D Printer CNC Machine
- Current / Phase: 1.5A
- Step Angle(degrees): 1.8
- Phase: 2
- Type: Hybrid
- Certification: ROHS,CE
- Holding Torque: 4.2 KGCM
- Step angle accuracy: + - 5%(full step, not load)
- Resistance accuracy: + - 10%
- Inductance accuracy: + - 20%
- Temperature rise: 80deg Max(rated current,2 phase on)
- Ambient temperature: -20deg ~+50deg
- Insulation resistance:100M Min,500VDC
- Insulation Strength: 500VAC for one minute
- (Lead Screw)
- Lead Screw Material: 304 Stainless Steel
- Color: Sliver
- Diameter: 8mm
- Length: 300mm
- Lead of thread: 8mm.
SC10UU 10mm Linear Motion Bearing Slide Bushing Block
TB6560 4 Axis Cnc Controller 4 Axis Stepper Motor Driver DSP Controlled 3.5A 24V
- Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
- the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
- circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
- 3.3A 4A 4.5A to accommodate more and different motor Current.
- The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.