Showing all 5 results

16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi

600.00 inc. GST
  • Adjustable frequency PWM up to about 1.6 kHz
  • 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
  • Configurable push-pull or an open-drain output
  • The output enable pin to quickly disable all the outputs
  • Terminal block for power input
  • Reverse polarity protection on the terminal block input
  • Green power-good LED
  • 3 pin connectors in groups of 4 so you can plug in 16 servos at once
  • Chainable design
  • A spot to place a big capacitor on the V+ line
  • 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
  • This board/chip uses an I2C 7-bit address between 0x60-0x80, selectable with jumpers.

5-36v Switch Drive High-power MOSFET Trigger Module

400.00 inc. GST
 
  • Operating Voltage: DC 5V - 36V;
  • The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support.
  • Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
  • Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
  • PWM, motor speed control, lamp brightness.
  • Availability: unlimited switch
  • Operating temperature: -40-85
  • Dimension: 34mm x 17mm x 12mm
  • The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
  • Wide voltage, the perfect support for PWM
  • Easily control high power devices
  • Input PWM to achieve motor speed control, lamp brightness control

Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)

899.00 inc. GST
  • Driver Model: VNH3ASP30
  • Current sensing available to Arduino analogue pin
  • Operating Voltage: 12 V to 16V DC
  • Peak Current: 14A
  • Continuous Current: 30A
  • of Channels: 2
  • Maximum PWM frequency: 20 kHz
  • MOSFET on-resistance: 19 m (per leg)
  • Thermal Shutdown protection
  • Under-voltage and Overvoltage shutdown.
  • LED Indicator
  • Dimensions: 60 x 54 x 12mm
  • Weight: 19gm

IRF520 MOSFET DRIVER MODULE SENSOR

130.00 inc. GST
  • Operating Voltage: 3.3v & 5v
  • Digital level port
  • Output load voltage: 0-24v
  • Output load current: <5A
  • The heat sink is added for currently more than 1A
  • Compatible with Arduino, MCU, ARM, Raspberry pi
  • PWM dimming LED used to step-less dimming, variable-speed motor
  • Output PWM can be adjusted by the original IFR520 MOS
  • Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
  • Dimension:34*30*18mm
  • Size: 10gm

VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver

900.00 inc. GST
  • Driver Model: Monster Moto Shield VNH2SP30
  • Operating Voltage: 12V to 16V DC
  • Maximum current rating: 30 A
  • Continuous Current: 14 A
  • Number of Channels: 1
  • MOSFET on-resistance: 19 m (per leg)
  • Maximum PWM frequency: 20 kHz
  • Current sensing available to Arduino analog pin
  • Thermal Shutdown
  • Under voltage and Overvoltage shutdown.
  • Dimensions: 55 x 28 x 12mm
  • Weight: 15gm