GSM
SIM800L GPRS GSM Module
- Chip: SIM800L
- Operating voltage: 3.7V -4.2V
- Current : 2A
- Quad-band (850/900/1800/1900MHz) supports
- Searches for network and login automatically
- Can connect any global GSM network with 2G sim
- Miniature size
- AT command interface with auto baud detection
- Lead-out buzzer and vibration motor control port
- Scan and receive FM radio broadcast, send and receive SMS and call
- Power consumption:
- Interface: UART (max 2.8V, serial interface)
- Command support: 3G PP TS 27. 007, 27. 005 and SIMCOM enhanced AT commands
- Sim Card Slot: Micro SIM
- Temperature range: -40℃ to 85℃
GSM Modem SIM 300
- Uses SIM300 GSM module transmission.
- Operating Voltage: 7 – 15V AC or DC (board has onboard rectifier).
- Comes with an onboard wire antenna for better reception.
- Can be used for Data/Fax, GSM based Voice communications, TCP/IP stack, GPRS and SMS
- SIM300 allows an adjustable serial baud rate from 1200 to 115200 bps (9600 default).
- Provides RS232 interface for connection to computers and other devices.
- Lithium Battery holder
- Can add external antenna with SMA connectors.
- Power, RING and Network LEDs for easy debugging.
- Provides serial TTL interface for easy and direct interface to microcontrollers.
- Can be controlled through standard AT commands.
GSM Antenna
GSM Modem Sim900
- Quad-Band GSM/ 850/900/1800/1900MHz
- Voice Communication Port
- On-Board Voltage Regulator
- Power/Single LED indication
- SMA Connector for Antenna connection
- Compatible with Arduino, raspberry pi, arm, avr, pic, 8051
- Power Supply 12v 1amp to 2 amps max
- Use in the area of full signal strength.
- Perfectly suited for GSM-based Microcontroller Projects (better than SIM300 and other GSM Modems)
- Option for connecting MIC and SPEAKER directly to GSM MODEM for calls (LINE IN also available)
- Supports communication through RS232 with DB9 Connector, TTL Pins and I2C Pins
- CALL SMS GPRS facility - MIC input, LINE input and SPEAKER output pinsX
SIM900A 5V V4.0 Kit Wireless Extension Module GSM GPRS Board Antenna Tested
GSM GPRS + Camera Module A6C Breakout
- Operating Voltage: 3.3V – 4.2V
- Working Temperature: -30 ℃ to +80℃
- Boot Voltage: >3.4V
- Standby Current: less than 3 mA
- GSM/GPRS Frequency Band: including 850, 900, 1800, 1900 MHZ
- GPRS Class 10
- Sensibility: <-105
- Voice Call: Support
- SMS message: Support
- GPRS maximum speed: Download speed 85.6Kbps, Upload speed 42.8Kbps
- AT Command: Support standard GSM07.07, 07.05, and extended Ai Thinker command
- 2 UART: one for download, one for AT command
- Audio: Support digital and analog audio, support HR, FR, EFR, AMR audio code
- Camera resolution: 0.3M
MEPUNO COMMUNICATION BOARD
- Microcontroller ATMEGA328 P
- Crystal for microcontroller: 16 MHZ
- USB type B connector
- On-Board Power LED Indicator
- 5volt, 12 volt regulated circuit
- Two separate regulated 5volt power supply
- On Board On/Off switch
- On Board DC jack for powering up using adaptors
- On Board Reset Switch
- On Board TX/RX indication LEDs
- On board FTDI Driver for adruino
- Berg headers for external interfacing
- Supports I2C /GSM /GPS/RF/USART serial communication
- Separate berg headers available for PIR, Servo motor, RTC/I2C, GPS_TTL, and USART-TTL
- Four 3pin PBT Connectors
- Four SPDT 12V Relays
- Onboard DB9 connectors for GPS, GSM and USART communication
- Berg slot for 16x4 LCD connections
- Onboard TRIM-POT for LCD
- Onboard RTC IC: IN1307 with crystal 32768 MHZ crystal and CR2302 battery
SIM800A Quadband GSM / GPRS Module convertible as Shield for Arduino
- Quad-Band GSM/GPRS 850/ 900/ 1800/ 1900 MHz.
- GPRS class 2/10.
- Input Voltage: 9V-12V DC.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- 5V interface for direct communication with MCU kit.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
- SMA connector with GSM L Type Antenna.
- Headphone jack for audio out.
- Li-Po battery 3.7-volt pins for supply.
- Li-Po battery USB charger (3.7volts).
- CP2102 port for communication with a laptop.