I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-10%
SC10UU 10mm Linear Motion Bearing Slide Bushing Block
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Black PLA 1.75 mm 1 Kg Filament For 3D Printer Wanhao
Original price was: ₹1,800.00.₹1,500.00Current price is: ₹1,500.00. inc. GST
100K ohm NTC 3950 Thermistor/Temperature Sensor for Reprap 3D printer Extruder
Original price was: ₹100.00.₹90.00Current price is: ₹90.00. inc. GST
- High-temperature Teflon wire temperature: 200 degrees
- Nominal resistance R25 (25 ℃): 100k
- Resistance accuracy: ± 1%
- B value R25 / 50: 3950k
- B value accuracy: ± 1%
- Operating temperature range: -40 ℃ ~ +300 ℃
- Dissipation power factor: ≥ 5 mW / ℃ (static air)
- Thermal time constant: ≤ 7S (static air)
- Maximum rated power: 45mW
- Wiring length: 1 meter
- Material: glass glaze film
Description
This 100K ohm NTC 3950 Thermistor/Temperature Sensor designed specifically for Reprap 3D printer Extruder or Heated Bed. This thermistor Conviniently pre-wired with 1 meter long high-temperature PTFE insulated wiring. Moreover, this offers a wide range of applications in 3d printing and often used with a heated bed or extruder. The Stainless steel tube encapsulation protects the probe from waterproof moistureproof thus prevents rust. This compact-sized, easy to install temperature sensor fairly precise ±0.5°C over much of the range.
Hence the temperature can be measured with a precision of 0.0625 C. It can give output is digitally accurate to 12 bits of precision from the onboard digital-to-analog converter. Here the NTC thermistor made up of think material with the heating rod made up of high-quality material. This temperature sensor module offers high sensitivity, and has a swift response, 1 percent, with a resistance value at 25°c= 100k. It uses adaptive thermosensitive material with high-quality wiring insulation with high temperature  Teflon/ PTFE
Reviews (0)
Shipping & Delivery
Related products
AM2302 WIRED MODULE
- Low cost
- 3V to 5V power and I/O
- 5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- 3 wires 23cm long (9")
- Dimensions: 27x 58.75 x 13.30mm
DS1820 Temperature Sensor
- Unique 1–Wire interface requires only one port pin for communication
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Can be powered from the data line
- Zero standby power required
- Measures temperatures from –55° C to +125° C in 0.5° C increments.
- Temperature is read as a 9–bit digital value.
- Converts temperature to digital word in 200 ms (Typ.)
- User-definable, nonvolatile temperature alarm settings
- Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature alarm condition)
DS18B20 MODULE
- Resolution: 9bits to 12bits (Selectable)
- Supply Voltage (V): 3 to 5.5
- Temperature Range(°C): -55 to +125
- Measuring Accuracy(°C): ±0.5
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into the chip
- Multiple sensors can share one pin
- Maximum conversion time and response: 750 ms
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Digital signal output
- 18B20 Temperature Sensor Chip
- Send data via a pin
- User-definable nonvolatile (NV) alarm settings
- Dimension: 19*15*6cm
- Weight: 9gm
GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
LM35 SENSOR
- Calibrated Directly in Celsius (Centigrade)
- Operates from 4 V to 30 V
- Linear + 10-mV/°C Scale Factor
- ±0.5°C Ensured Accuracy (at 25°C)
- Can measure temperature ranging from -55°C to 150°C
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load.
- Drain current is less than 60uA
- The output voltage is directly proportional (Linear) to temperature (i.e.) there will be a rise of 10mV (0.01V) for every 1°C rise in temperature
- Suitable for Remote Applications
- Low-cost temperature sensor
- Available in TO-92, TO-220, TO-CAN, and SOIC package
NEMA 23 10.1 kg-cm
- Operating Voltage : 2.3 Volts
- Step Angle : 1.8°
- Holding Torque : 10.1 kg-cm
- Supply Current (A) : 2.8 Ampere/Phase
- Number of Leads : 4
- Inductance : 2.2 mH/Phase
- Resistance : 0.83 Ohm
- Rotor Inertia : 275 gm-cm2
- Weight (gm) : 650
- Detent Torque (kg-cm) : 0.36
- Frame Size (mm) : 57 x 57
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Shaft Diameter (mm) : 6.35
- Shaft Length (mm) : 20.6
- Step Angle Accuracy : ±5%
- Comparably more powerful than NEMA17 motors.
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Reviews
There are no reviews yet.