I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
74LS14 Hex Inverter IC
₹15.00 Original price was: ₹15.00.₹13.00Current price is: ₹13.00. inc. GST
- Hex Inverter
- High-level input voltage:Â 2V
- Low-level input voltage:Â 0.8V
- High-level output current:Â -1mA
- Low-level output current:Â 20mA
- No. of gates:Â 6
- No. of inputs:Â 6
- No. of outputs:Â 6
- Propagation Delay:Â 7ns
- Supply voltage range:Â 4.5 to 5.5V
- Package:Â DIP-14
- Six Independent INVERT Gates
- Fast Switching Times
- Operating Temperature up to 70°C
- Standard TTL Switching Voltages
The 74LS14 designed as a Hex Inverter (NOT gate) belongs to the 74XXYY IC. This IC comes with six NOT gates inside it and every gate provides one input and one output pin. That mean it consists of six inverters that perform logical invert action. The output of an inverter is complement of its input logic state i.e. when input is high its output is low and the other way around .
In this, the device contains six independent gates each of which performs the logic INVERT function. When operating at 5V, the minimum high-level input voltage is 4.75V, and therefore the maximum low-level input voltage is 5.25V. 74LS14 function using a single power supply to all the triggers and used to operate with any TTL based device. Each input offers hysteresis that increases the noise immunity and transforms a slowly changing input signal to a fast-changing, jitter-free output. These circuits easily operates easily in any environment and triggered easily with the slowest input ramps.
A Schmitt Trigger designed as a comparator-based circuit that gives the output on the basis of the previous gate output. In a Schmitt Trigger, the input value exist as analog or digital but the output always comes in two forms 1 or 0. By applying a positive feedback system, any circuit is convertible to Schmitt trigger. In a Schmitt Trigger circuit, the threshold used to obtain the output. When the value is greater than the threshold the output remain HIGH otherwise it will be considered in the LOW state.Â
Applications
- These ICÂ used for Noise Removing.
- Widely used in Power meter and Power analyzers.

Related products
120pcs 12 value 1uF-470uF Electrolytic Capacitor Kit 1UF 2.2UF 3.3UF 4.7UF 10UF 22UF 33UF 47UF 100UF 220UF
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
4 Pin RMC Connector
74LS540 High-Speed CMOS Logic Octal Buffer and Line Driver IC
GSM Antenna
GSM Antenna Dlenp 2dbi/3dbi Patch Antenna with SMA Male Connector
- GSM Antenna
- Gain: 2 to 3dbi
- Wire Length: 3 metre
- 3dbi Sticker Antenna
- GSM Antenna
- SMA Male Connector
- Frequency Range(MHz): 824-960/1710-1990Mhz
- Bandwidth (MHz): 136/280
- VSWR≤1.5
- Gain(dB): 2-3dbi
- Max Input power(W): 60W
- Input Impedance: 50 Ω
- Polarization Type: Vertical
- Cable Type: RG174
- Mounting Adhesive
- Net weight: 47g
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board

Reviews
There are no reviews yet.