I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-35%
74LS242 Quad Bus Transceiver IC
Original price was: ₹38.00.₹25.00Current price is: ₹25.00. inc. GST
74LS245 Octal Bus Transceiver IC
Original price was: ₹49.00.₹40.00Current price is: ₹40.00. inc. GST
74LS243 Quadruple Bus Transceiver IC
Original price was: ₹23.00.₹15.00Current price is: ₹15.00. inc. GST
- Quadruple Bus Transceivers
- Logic Family:Â LS
- Number of Circuits:Â 4
- Output Type:Â 3-State
- High Level Output Current:Â -15 mA
- Low Level Output Current:Â 24 mA
- Polarity:Â Non-Inverting
- Propagation Delay Time: 18 ns
- No. of Pins:Â 14
- Operating Temperature Range: 0°C to +70°C
- Â Supply Voltage Range:Â 4.75V to 5.25V
- Package:Â DIP-14
Description
The 74LS243 designed as Quad Bus Transmitters/Receivers designed for 4-line asynchronous 2-way data communication between data buses. 74LS243 also used to drive terminated lines down to 133 Ohm. 74LS243 Quadruple Bus Transceiver IC belongs to 74XXYY IC series. The 74LS243 IC operates at a wide range of working voltage, a wide range of working conditions. And directly interfaces with CMOS, NMOS, and also TTL. The output of the IC always comes in TTL. Thus bmakes it quite easy to function with other TTL devices and microcontrollers. Moreover, these IC 74LS243 comes as smaller in size and offers much faster speed which makes it highly reliable in every kind of device.
74LS243 IC operates at a supply voltage at a range between 4.75V and to a maximum of 5.25V. This IC designed for operation over the full military temperature range of −0°C to 75°C. 74LS243 manufactured in 14−pin plastic PDIP wide-body surface-mount packages.
Bus transceivers designed as electronic tri-state bi-directional devices that allows the flow of data between two points. This makes them compatible with bus-oriented systems or the bi-directional (input or output) control of interface circuitry. Moreover, bus transceiver exist as inverting or non-inverting, common examples are 74LS243 & LS242 IC series. Bus tranceivers are designed specifically for asynchronous two-way communication between two data buses or input/output device. The transceiver allows for the transmission of data from terminals A to terminals B or the reverse depending on the logic level at the direction-control input. These IC widely used to provide bidirectional, input or output control, of either digital or analogue devices to a common shared data bus.
Applications
- Building Automation
- Electronic Point of Sale
- Factory Automation and Control
- Test and Measurement protocols
Reviews (0)
Shipping & Delivery
Related products
74LS642 Octal Bus Transceiver IC
- Octal Bus Transceiver
- Output:Â Open-Collector
- Logic: Inverting
- High-level output voltage: 5.5V
- Low-level output voltage: 0.25V
- High-level output current: 0.1mA
- Low-level output current: 24mA
- Input clamp voltage: -1.5V
- Propagation Delay Time Max.: 60ns
- Supply voltage range: 4.75 to 5.25V
- Package: DIP-20
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
![RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]](https://www.mathaelectronics.com/wp-content/uploads/2021/02/ROBOSOFT-LABS-RF-RX-TX-ENCODER-DECODER-MODULE-BOARD-SKURL5037-228x228-1.jpg)
RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]
- Operating voltage: 3.6~5.5v ( 5v recommended),
- Receiver sensitivity as high as -110dbm,
- Compatible with HT12E and HT12D,
- Low power and good range.
- High-frequency stability and low coherence and interference
- Easy interfacing with the RF modules, using the female headers for placing the modules.
- Breakout pins for connecting to the microcontroller.
- DIP Switch for Address Selection (when multiple modules are used at one location)
- Status LED for valid transmit.
- Supports both ASK, FSK RF modules
- Small size, high quality PCB.
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.
Reviews
There are no reviews yet.