I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-35%
74LS242 Quad Bus Transceiver IC
Original price was: ₹38.00.₹25.00Current price is: ₹25.00. inc. GST
74LS245 Octal Bus Transceiver IC
Original price was: ₹49.00.₹40.00Current price is: ₹40.00. inc. GST
74LS243 Quadruple Bus Transceiver IC
Original price was: ₹23.00.₹15.00Current price is: ₹15.00. inc. GST
- Quadruple Bus Transceivers
- Logic Family:Â LS
- Number of Circuits:Â 4
- Output Type:Â 3-State
- High Level Output Current:Â -15 mA
- Low Level Output Current:Â 24 mA
- Polarity:Â Non-Inverting
- Propagation Delay Time: 18 ns
- No. of Pins:Â 14
- Operating Temperature Range: 0°C to +70°C
- Â Supply Voltage Range:Â 4.75V to 5.25V
- Package:Â DIP-14
Description
The 74LS243 designed as Quad Bus Transmitters/Receivers designed for 4-line asynchronous 2-way data communication between data buses. 74LS243 also used to drive terminated lines down to 133 Ohm. 74LS243 Quadruple Bus Transceiver IC belongs to 74XXYY IC series. The 74LS243 IC operates at a wide range of working voltage, a wide range of working conditions. And directly interfaces with CMOS, NMOS, and also TTL. The output of the IC always comes in TTL. Thus bmakes it quite easy to function with other TTL devices and microcontrollers. Moreover, these IC 74LS243 comes as smaller in size and offers much faster speed which makes it highly reliable in every kind of device.
74LS243 IC operates at a supply voltage at a range between 4.75V and to a maximum of 5.25V. This IC designed for operation over the full military temperature range of −0°C to 75°C. 74LS243 manufactured in 14−pin plastic PDIP wide-body surface-mount packages.
Bus transceivers designed as electronic tri-state bi-directional devices that allows the flow of data between two points. This makes them compatible with bus-oriented systems or the bi-directional (input or output) control of interface circuitry. Moreover, bus transceiver exist as inverting or non-inverting, common examples are 74LS243 & LS242 IC series. Bus tranceivers are designed specifically for asynchronous two-way communication between two data buses or input/output device. The transceiver allows for the transmission of data from terminals A to terminals B or the reverse depending on the logic level at the direction-control input. These IC widely used to provide bidirectional, input or output control, of either digital or analogue devices to a common shared data bus.
Applications
- Building Automation
- Electronic Point of Sale
- Factory Automation and Control
- Test and Measurement protocols
Reviews (0)
Shipping & Delivery
Related products
74LS642 Octal Bus Transceiver IC
- Octal Bus Transceiver
- Output:Â Open-Collector
- Logic: Inverting
- High-level output voltage: 5.5V
- Low-level output voltage: 0.25V
- High-level output current: 0.1mA
- Low-level output current: 24mA
- Input clamp voltage: -1.5V
- Propagation Delay Time Max.: 60ns
- Supply voltage range: 4.75 to 5.25V
- Package: DIP-20
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
NRF24L01 Long Range
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km.
- Transmission mode current(peak): 115mA
- Receiver Mode Current(peak): 45mA
- Power-down mode current: 4.2uA
- Sensitivity 2Mbps mode in received: -92dBm
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
- Support six-channel data reception.
- 2Mbit/s speed makes high-quality VoIP possible
- Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
- Supports 126 RF channels
- Onboard antenna for optimum performance
- Standard DIP type pinout for easy Interface through jumper wires or breadboard
- Small size: 16.5mm*45.5mm.
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
Reviews
There are no reviews yet.