I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
74LS374 Edge-Triggered D Flip-Flop IC
₹23.00 Original price was: ₹23.00.₹18.00Current price is: ₹18.00. inc. GST
- Edge-Triggered D Flip-Flop
- High-level input voltage:Â 2V
- Low-level input voltage:Â 0.8V
- High-level output voltage:Â 5.5V
- High-level output current:Â -6.5mA
- Input clamp voltage:Â -1.2V
- Maximum clock frequency:Â 100MHz
- Propagation delay time:Â 18ns
- Supply voltage range:Â 4.75 to 5.25V
- Package:Â DIP-20
74LS374 Edge-Triggered D Flip-Flop IC 8-bit registers feature 3-state outputs designed explicitly for driving highly capacitive or relatively low-impedance loads. The high-impedance 3-state and increased high-logic-level drive provide these registers with the potential of connected on to. And driving the bus lines during a bus-organized system without need for interface or pullup components. These devices are particularly attractive for implementing buffer registers, I/O ports, bidirectional bus drivers, and dealing registers.
The eight flip-flops of the 74LS374 designed as edge-triggered D-type flip-flops. On the positive transition of clock, the Q outputs set to logic states that set up at the D inputs. Schmitt-trigger buffered inputs at the enable/clock lines of the ’74LS374 devices simplify system design as ac and dc noise rejection improved by typically 400 mV because of the input hysteresis. Moreover, the buffered output-control (OC’) input often accustomed place the eight outputs in either a standard logic state (high or low logic levels). Or the high-impedance state. within the high-impedance state, the outputs neither load nor drive the bus lines significantly. Meanwhile, OC’ does not affect the internal operation of the latches or flip-flops. That mean the old data retained or new data entered, even while the outputs turned off.
A D-type latch/flip-flop with two stable states that is designed as a timed latch. A D-type latch has a one-clock-cycle delay in its input. Delay circuits are frequently produced by cascading multiple D-type flip-flops. This was then used in a variety of applications, such as digital television systems. A D flip-flop, sometimes known as a delay flip-flop, is a D-type flip-flop.

Related products
120pcs 12 values 0.22UF-470UF Aluminum electrolytic capacitor assortment kit set pack
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
GSM Antenna
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.

Reviews
There are no reviews yet.