I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Motor for Micro FPV RC Quadcopter
₹200.00 Original price was: ₹200.00.₹150.00Current price is: ₹150.00. inc. GST
- Motor Diameter: 8.5mm
- Motor Length: 20mm
- Shaft Diameter: 1.0mm
- Cable Length: 60mm
- Weight: about 5g
- Operating Voltage range: 3v to 3.7v DC
- Rated Speed – 39000 RPM
- Propeller length: 75mm
- This coreless motor supports 1S battery.
- Ideal for mini quadcopter projects weighing below 60 grams
Propeller is designed as a lightweight brushed DC coreless motor. These coreless motor works perfectly for a small drone, offering you an excellent affordable price when compared with costly BLDC motors. This Magnetic Micro Coreless Motor for Micro FPV RC Quadcopter is a very compact and lightweight DC motor nicely crafted for perfectly matching your small 100mm multirotor frames. This coreless motor comes with high-quality magnets and supports a 1s battery.
This is much more required to lift and push the drone to the target. And these are less noisy with low resistance. The only disadvantage of using coreless is the amount of torque they provide, as they are High Speed and Low Torque motors.
Propellers are designed as high-quality propellers explicitly for Micro FPV RC Quadcopter. These Props are lightweight and of high strength providing an angle of 15° design at the end of the propeller. These propellers are widely used for lower RPM motor and slow-flying drone models. The wide and thin blades of the propeller in their size category make them highly flexible in crash conditions. Thus they do not break easily. Propellers Black especially draws a larger amount of currents. And as a result, gives a considerable amount of thrust for the quadcopters.

Related products
2pcs x Small Rubber Wheel for N20 Motor – 34×7 mm Diameter
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
Acrylic Bracket for OV7670 Camera Module
Flysky FS-i6 6 Channel
- Bandwidth (kHz): 500.
- RF Range (GHz): 2.40 ~ 2.48.
- No. of channels: 6.
- Remote controller weight (gm): 400.
- Power: 6V (1.5V AA*4).
- Antenna Length: 26mm * 2 (dual antenna).
- Transmitting Power: ≤ 20dBm.
- RF Receiver Sensitivity: -105dbm.
- Entry-level 6 channel 2.4GHz radio with telemetry capability.
- Easy to use Programming & Navigation Buttons.
- Supports Heli/Standard Wing/Elevon/V-Tail.
- 20 Model Memory.
- 8 Character Model Name.
- Trainer and charging ports.
- The backlight LCD screen displays real-time transmitter and receiver voltage.
- 4 Stick Mode Selectable.
Flysky FS-TH9X 9Channel With FS-R8B
- Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module
- Receiver: FS-R8B
- Default Mode: Mode-2
- Input Power: 12V DC (1.5V x 8 AAA Battery)
- Bidirectional System
- Frequencies-Hopping
- Omni-directional High Gain Antenna
- Low Power Consumption
- Colour: Black
- Charger Port: Yes(DC Port)
- Data Output: PPM
- Channel Resolution: 4096
- Channel Delay: Better than 30us
- Display: STN VA-73 39mm LCD
- DSC port: 3.5mm:output:PPM
- Dimension:185*220*110mm
- weight: 690gm
Landing Gear
Metal mechanical Arm Gripper claw
- Metal Gripper Robotic Arm
- Operating Voltage: 4.8V to 6.6V
- Material: Aluminum Alloy
- The Kit comes with hardware, unassembly
- Clamp Max open: 55mm
- Clamp total length:108mm
- Clamp total width:98mm (when the Clamp open
- Light weight plank kit
- Compatible with HS322, HS422, MG995, SG5010 servo
- Degree of Freedom (DOF): 2
- Bearing Type: Ball Bearing
- Weight: About 68g
Power Distribution Board
- Material: glass fiber
- Easy connections from the battery to your ESC, video Transmitter, Flight Controller,
- LED power indicators
- Switches to control LEDs, video Transmitter power, etc.
- Can connect 1-8 ESC.
- Onboard switching voltage regulator
- Hole Spacing: 45mm Square and 35mm Square (Compatible with KK 45mm spacing)
- Dimensions : 50 x 50 x 2 mm.
- Weight: 8 gm.

Reviews
There are no reviews yet.