I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Motor for Micro FPV RC Quadcopter
₹200.00 Original price was: ₹200.00.₹150.00Current price is: ₹150.00. inc. GST
- Motor Diameter: 8.5mm
- Motor Length: 20mm
- Shaft Diameter: 1.0mm
- Cable Length: 60mm
- Weight: about 5g
- Operating Voltage range: 3v to 3.7v DC
- Rated Speed – 39000 RPM
- Propeller length: 75mm
- This coreless motor supports 1S battery.
- Ideal for mini quadcopter projects weighing below 60 grams
Propeller is designed as a lightweight brushed DC coreless motor. These coreless motor works perfectly for a small drone, offering you an excellent affordable price when compared with costly BLDC motors. This Magnetic Micro Coreless Motor for Micro FPV RC Quadcopter is a very compact and lightweight DC motor nicely crafted for perfectly matching your small 100mm multirotor frames. This coreless motor comes with high-quality magnets and supports a 1s battery.
This is much more required to lift and push the drone to the target. And these are less noisy with low resistance. The only disadvantage of using coreless is the amount of torque they provide, as they are High Speed and Low Torque motors.
Propellers are designed as high-quality propellers explicitly for Micro FPV RC Quadcopter. These Props are lightweight and of high strength providing an angle of 15° design at the end of the propeller. These propellers are widely used for lower RPM motor and slow-flying drone models. The wide and thin blades of the propeller in their size category make them highly flexible in crash conditions. Thus they do not break easily. Propellers Black especially draws a larger amount of currents. And as a result, gives a considerable amount of thrust for the quadcopters.

Related products
2pcs x Small Rubber Wheel for N20 Motor – 34×7 mm Diameter
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
Acrylic Bracket for OV7670 Camera Module
CC3D flight Control
- Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Supported by powerful OpenPilot GCS
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spectrum satellite receiver support.
- Futaba S-BUS hardware support.
- With a function of being directly plugged into the satellite receiver
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits on-board EEPROM for configuration storage.
F450 Quadcopter Frame
- Model: F450
- Frame width: 450mm
- Frame height: 55mm
- Frame Weight: 282g
- Take-off Weight: 800g ~ 1200g
- Motor Mount Bolt Holes: 16/19mm
- Landing Gear Height: 150mm
- Landing Gear Weight: 90gm
- Made by advanced engineering material, super strong & smooth.
- High quality and strong ability of anti-fall, lower maintenance cost.
- Compact design with small numbers of components, you can assemble it by yourself quickly and easily.
- Recommended Propeller: 10x4.5in;8x4.5in
- Recommended Battery: 3S~4S LiPo
- Recommended Motor: 22x12mm (Stator size)
- Recommended ESC: 20A/30A ESC
MR.RC 12A ESC
- Input Voltage: 2-3S LIPO
- Working Current: 12A
- Burst current (10S): 15A
- BEC: 5V / 1A Programmable: Yes
- With stable performance, it is practical and durable
- Offer you high compatibility, reliability, and stability
- Throttle range can be set to be compatible with different receivers.
- Equipped with built-in linear BEC or switch BEC.
- Easy to install and convenient to use
- Play a significant role in driving and controlling the motor to complete all kinds of instructions
- Suitable for 250 Mini four-axis and F330 aircraft, etc
- Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.
- Dimensions:38 x 20 x 6 mm
- Weight: 30g
Smart Robot Car Chassis Kit 2 Wheels
- This car is the tachometer encoder.
- Works with a 4 AA battery box (batteries not included).
- Used for distance measurement, velocity.
- Can use with other devices to realize the function of tracing, obstacle avoidance, distance testing, speed testing,
- Wireless remote control.
- Laser Cut Acrylic Chassis
- Two Dual Shaft Motors For Either Side
- Universal Castor To Avoid Slippage
- Placeholders For Different Sensors, Servos, and Modules
- Has Strong Torsion, With 130 Strong Magnetic Dc Motor. Speed Ratio 1: 48
- Size: 21 x 15 cm (L x W).
- Wheel size: 6.5 x 2.7cm (Diameter x Height).

Reviews
There are no reviews yet.