I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
A2212 BRUSHLESS DC MOTOR 1000KV
₹700.00 Original price was: ₹700.00.₹600.00Current price is: ₹600.00. inc. GST
- Motor KV: 1000
- Operating voltage: 7.2V to 12V (2 to 3Li-poly or 6to10 NiCad)
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of a three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 800gms approx
- Thrust @ 3S with 0945 propellers: 475gms approx
- Thrust @ 3S with 0845 propellers: 475gms approx
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
A2212 Brushless DC Motor 1000KV is a low cost, a high-speed brushless motor designed explicitly for Quadcopters, Drones, or toy planes. This brushless motor is said to be an OUTRUNNER type as its outside case rotates while the inside stays fixed. It is one of the prominent models in the market preferred for small drones and planes. The model is available at different speeds and can be chosen appropriately based on our application. A2212 (BLDC) Brushless DC Motor is a 1000kV motor that features high performance, superpower, and brilliant efficiency.
These A221 DC motors are suitable for medium size quadcopters with 8 inches to 10-inch propellers. Without a 3S LiPo battery, using 30A ESC and high efficiency 10″ propellers, can generate up to 800gms. This means using 4 of these motors on a quadcopter with 10″ propellers will give you a total of 3.2 kg thrust. This helps to build powerful and efficient quadcopters. This A2212 Brushless DC Motor 1000KV perfect with our F450 quadcopter frame and with  30A ESCs that can be used to drive the motor.
As this A221 DC motors available at a low price, but this motor recognized with its low-quality bearings and magnets. As a result produces noise and vibration. And also become warm while operating at high speed. But all these defects are minor and don’t affect motor performance. The A2212 1000Kv BLDC Motor equips a shaft of 3.7mm for the drone. A221 DC motors designed with a solid metal case, thus makes them highly reliable and durable in a crash. An open wire end is provided on the motor for customizing connections.
APPLICATIONS
- Drones
- QUADCOPTERS
- Robotics
- Toy planes

Related products
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
NEMA 17 5.5 kgcm
- Step Angle : 1.8°
- Holding Torque : 5.5 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :1.5 Ampere
- Number of Leads : 6
- Inductance : 5.5 mH
- Resistance : 2.8 Ohms
- Weight (gm) : 363
- Detent Torque (kg-cm) : 2.6
- Frame Size (mm) : 42 x 42
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Step Angle Accuracy : ±5%
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 22
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor NEMA 34 122 kg-cm Hybrid Bipolar
- Rated Voltage:4.08V
- Phase: 2
- Current/ phase: 4A
- Holding Torque: 122 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 37mm
- Shaft Diameter: 13mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
Stepper Motor NEMA 34 68 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Holding Torque: 68 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip
Towerpro MG90S Mini Digital 180 Degree Servo
- Model: MG90S
- Operating voltage: 4.8V~ 6.6V
- Servo Plug: JR
- Stall torque @4.8V : 1.8kg-cm
- Stall torque @6.6V : 2.2kg-cm
- Modulation: Analog
- Dimensions: 23.1*12.2*29.0 mm
- Gear Type: Metal
- Rotation/Support: Dual Bearings
- Rotational Range: 180°
- Pulse Cycle: 20 ms
- Pulse Width: 400-2400 µs
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
- Weight: 13 gm

Reviews
There are no reviews yet.