I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Bullet Connector 3.5MM
₹80.00 Original price was: ₹80.00.₹40.00Current price is: ₹40.00. inc. GST
- Diameter: 3.5mm
- Length:1.5CM & 1.5CM
- Amperage Rating: 60A -180Amps
- Hook up RC Battery to Electronic
- Hook up Brushless motor to electronic speed control
- These have low resistance and gives the best electric flow
- 5mm gold connectors Male
- 5mm gold connectors Female
- Dimension: 2.7*2.1*3inch
- Weight: 67gm
Bullet connectors 3.5mm are used to provide solid and quick electrical connections by snapping together easily and hold tightly. These are suitable to make a tight connection in high power applications. Bullet connectors consist of two parts: a bullet-shaped male end and a socket-shaped female end. 3.5mm bullet connectors are bullet connectors with a diameter of 3.5mm and a rated current of 80 A. These connectors are useful for connecting small ESCs to motors or connecting another low amperage wiring. This bullet connector pack comes with 1 male and 1 female 3.5mm bullet connectors. In order to secure the attachment, we need to solder the connector. These 3.5mm bullet connector offers low resistance, as a result, gives the best electric flow. It operates at an amperage rating of 60A -180A.
3.5mm connectors are capable of handling twice the current than 2.5mm bullet connectors. These connectors used as Male Hook up RC Battery to Electronic Hook up, brushless motor to control electronic speed.

Related products
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
DYS Motor D2826 1400KV
- Item name: D2826 1400KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt:205W
- Max Current: 19A
- Suggested prop: 9045
- Pull: 660g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 7x4(3S) ~ 9x4.7 (2S)
- ESC: 40A
- Ri(M ): 0.078
- Pull: 780g
- Shaft: M5
- Motor Mount Holes: 16mm or 19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
Minebea 16PU-M202 Bipolar Stepper Motor
- Step angle 3.75 degree
- Phase current: 0.6 ampere
- Step Angle: 3.75 Degree +/- 5%
- Drive Sequence: Bipolar
- Rated Current per Winding: 0.6 A
- Winding Resistance: 5E5
- Holding Torque Nm (Kg-cm): 0.064 (0.65)
- Rotor Inertia (Kg-cm2): 0.015
- Rated Voltage: Max 40V DC, 12V Typical
- Flange Size: 56.5 mm
- Shaft (with coupling spur gear): 5mm
- Connecting Wire Length: 30 cm
- Holding Torque: 0.074 nm
NEMA 17 1.6 kgcm
- Operating Voltage : 12~16 V
- Step Angle : 1.8°
- Holding Torque : 1.6 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :0.31 Ampere
- Number of Leads : 6
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor NEMA 34 46 kg-cm Hybrid Bipolar
- Rated Voltage:4.2V
- Current/ phase: 4A
- Inductance/ phase: 7.3mH
- Resistance/ phase: 0.87ohms
- Holding Torque: 46 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- They are high torque stepper motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing

Reviews
There are no reviews yet.