I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
CT1270 AC/DC Current Sensor
- Supply voltage: 5v DC
- Output: Analog Dc Voltage
- Small size
- Pass Wire Through Hole
- Get DC analogue Voltage Vcc and GND
- Compatible with Arduino, Raspberry Pi, AVR, ARM,8051, PIC
Description
A current sensor is designed to detect electric current AC/DC in a wire and thus generates a signal proportional to it. This generated signal could be analogue voltage or current or even digital output. Current Sensor basically used to measure and calculate the amount of current applied to the conductor without affecting the performance of the system. This current sensor operates at a supply voltage of 5V in which output is proportional to AC or DC current. CT1270 is used in a wide range of applications where sensing and controlling current flow is fundamental such as displaying the measured current in an ammeter. And also stored for further analysis in a data acquisition system or can be utilized for control purposes.
The present output current signal is read via the analogue I / O port of a microcontroller or an Arduino. Moreover, this current sensor module works perfectly with Arduino, Raspberry pi, AVR, ARM,8051, PIC and can be interfaced easily.
APPLICATIONS
- Ammeters
- Current control purposes
Reviews (0)
Shipping & Delivery
Related products
DS18B20 MODULE
- Resolution: 9bits to 12bits (Selectable)
- Supply Voltage (V): 3 to 5.5
- Temperature Range(°C): -55 to +125
- Measuring Accuracy(°C): ±0.5
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into the chip
- Multiple sensors can share one pin
- Maximum conversion time and response: 750 ms
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Digital signal output
- 18B20 Temperature Sensor Chip
- Send data via a pin
- User-definable nonvolatile (NV) alarm settings
- Dimension: 19*15*6cm
- Weight: 9gm
E-18-D80 NK Infrared sensor
- Model: E18-D80NK
- Input voltage: 5VDC
- Sensing range: 3 – 80cm
- Current Consumption: 300mA.
- Cable length: 1 m.
- Current: 100mA
- Pointing Angle: ≤ 15
- Appearance: threaded cylindrical
- Diameter: 18mm
- Length: 45mm
- Detection of object: transparent or opaque
- Output operation: normally open
- Diameter: 17MM
- Â Reverse polarity protection
- Digital Output.
- Can detect colour differences from a certain range.
- TTL output is low whenever the sensor senses an obstacle.
- External control circuit unnecessary.
- Diffuse reflective type.
- Low consumption.
- Operating temperature: -25℃ to 55℃
- Material: plastic
- Red: +5V; Yellow: Signal; Green: GND
LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
LM35 SENSOR
- Calibrated Directly in Celsius (Centigrade)
- Operates from 4 V to 30 V
- Linear + 10-mV/°C Scale Factor
- ±0.5°C Ensured Accuracy (at 25°C)
- Can measure temperature ranging from -55°C to 150°C
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load.
- Drain current is less than 60uA
- The output voltage is directly proportional (Linear) to temperature (i.e.) there will be a rise of 10mV (0.01V) for every 1°C rise in temperature
- Suitable for Remote Applications
- Low-cost temperature sensor
- Available in TO-92, TO-220, TO-CAN, and SOIC package
MQ5 SENSOR
- Power requirements: VCC - 5V±0.1
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0 .3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detection Gas: LPG, natural gas, town gas
- Detection Concentration: 300-10000ppm
- Heating voltage: 5V±0.1
-  Load resistance: 20KΩ
-  Heater resistance: 31±10%
- Â Heating consumption: less than 800mw
- Operating temperature:-10 to 50°C
- Related humidity less than 95%Rh
- Sensing Resistance: 10KΩ- 60KΩ (1000ppm CH4)
- Preheat time: Over 24 hour
TCRT5000
- Model TCRT5000
- Colour: Black + blue
- Operating Voltage Range: 3.6~5 VDC
- Package type: leaded
- Typical output current under test: IC = 1 mA
- Emitter wavelength: 950 nm
- Peak operating distance: 2.5 mm
- Detecting range: 0.591″ (15mm)
- Detecting method: Reflective
- Collector-Emitter: Voltage: 70V
- Collector Current: 100mA
- Forward Current: 60mA
- Output type: Phototransistor
- Lead (Pb)-free soldering released
- Daylight blocking filter
- Dimensions: 10.2 x 5.8 x 7mm
U Slot Sensor MOC7811
- Model HY860D
- Output Type Photo Transistor
- Peak Emission Wavelength: 940nm
- IR Diode Forward Current: 50mA
- IR Diode Reverse Voltage: 5V
- Transistor Power Dissipation: 75mW
- Transistor Collector Current: 20mA
- Photo Transistor Collector-emitter Voltage: 30V
- Photo Transistor Emitter-collector Voltage: 5V
- Diode Power Dissipation: 100mW
- Operating Temperature Range: -55~100 Celsius Degree
- Number of Pins 4
- Hole Diameter: 3mm
- Material: Plastic, Metal
- Non-Contact Switching
- For Direct PC-Board or Dual-In-Line Socket Mounting
- Fast Switching Speed
- Colour: Black
- Dimension: 22 x 22 x 6mm
- Weight: 8gm
Reviews
There are no reviews yet.