I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%
Water Float Sensor P43
Original price was: ₹200.00.₹175.00Current price is: ₹175.00. inc. GST
Water Level Sensor
Original price was: ₹200.00.₹175.00Current price is: ₹175.00. inc. GST
DN40 – 1.5” Water Flow Sensor
Original price was: ₹1,800.00.₹1,500.00Current price is: ₹1,500.00. inc. GST
- Model: YF-DN40
- Material: Plastic
- Function: Sensor, flow rate control
- Working Voltage: DC 5V~24V
- Thread size: BSP 1 1/2”
- Size:L 92x OD46 5″
- Colour: Black color
- Flow rate: 5~200L/min
- Flow Pulse: F(Hz)=(0.45xQ) +/-3% Q=L/min
- 1L water= 27Pulse
- Working Current: 15mA (DC5 V)
- Working Voltage: DC 4.5V
- Load Capacity: =10 mA (DC 5 V)
- Operating Working Temperature: -25 to +80 Degree C
- Liquid Temperature: 85
- Accuracy: 3~5%
- Working environment: water, liquid, light oil etc.
- Hydrostatic pressure> 1.75MPa meet
- Insulation resistance> 100M> 100M
- Accuracy in 1 ~ 120L / MIN ± 2% in line
- Flow pulse characteristics F = (0.45 * Q) Q = L / Min meet
- Weight: 146g
Description
A Float sensor defines as a simple water level indicator. This water level controller is used in a pump, an indicator, an alarm, or other devices. YF-DN40 1.5 inch Water Flow Measurement Sensor offers 5~200Litres/min Flow Rate used with hot waters, cold waters, warm waters, clean water, and dirty water also. These are arranged in line with your water line and consists of a pinwheel sensor to measure how much liquid has moved through it.
YF-DN40 works on the principle of the Hall Effect. This consists of a plastic body, a water rotor, and a hall-effect sensor. A water rotor along with a Hall Effect sensor senses and measure the water flow. As a result, when the water flows through the valve, the rotor rotates. This results in variation in the speed of the motor. Thus the integrated magnetic Hall Effect sensor in the sensor outputs an electrical pulse with every revolution. This variation is calculated as output as a pulse signal by the Hall Effect sensor. Thus, the rate of flow of water is measured. The Hall Effect sensor is protected from the water pipe ensuring the sensor stays safe and dry.
The water flow is calculated by counting the pulses from the output of the sensor. Each litre is approximately 27 pulses. Therefore the Flowmeters offers a wide range of applications for measuring water flow and is quite easy to build a water management system using the renowned water flow sensor YF-DN40. Moreover, YF-DN40 1.5 inch water flow sensor consists of three wires that can be easily interfaced easily with any microcontroller and Arduino board. It operates at a 5V Vcc supply providing pulse output.
Reviews (0)
Shipping & Delivery
Related products
250V Float Switch Sensor for Water Level Controller-Big
- Protection: Waterproof
- Medium Working Pressure: Max 1 Bar
- Circuit Breaking Capacity: Directly KW with 250V
- Medium Temperature: 70 Deg.C.
- Mechanical endurance: ≥100,000 times
- Electrical endurance: ≥500,000 times
- Cable length: 3m
- Corrosion Free,
- Sturdy and durable & need no maintenance.
- No current / voltage is passed through water, therefore no electrolysis or Salt deposition.
- Long life (approximate 10 million operations)
- Rust proof (entire sensor body in polypropylene)
- Used in hard water or fuel such as diesel, kerosene, oil etc.
- Dimensions : 11 x 9 x 5cms
- Weight 690 grams
DS18B20 PROBE
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12-bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into a chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
- Each pin uses a heat-shrinkable tube to prevent short circuit, internal sealing glue.
- Stainless steel tube encapsulation waterproof moistureproof prevents rust.
- Stainless steel tube 6mm diameter by 30mm long.
- Contains DS18B20 temperature sensor.
- Uses 1-Wire interface- requires only one digital pin for communication.
- Unique 64 bit ID burned into the chip.
- Multiple sensors can share one pin.
- Temperature-limit alarm system.
- Without the external components, the unique single bus.
Floating Ball Valve Automatic Float Valve Water Level Control Valve F/ Water Tank Water Tower
- Material: plastic
- Form: diaphragm type
- Connection form: thread
- Drive mode: float control
- Flow direction: one direction
- Nominal diameter:15mm
- Automatic control, less water from the fill, the water from the stop.
- Quarter of the inlet, a large amount of water.
- The appearance of fine, small size, practical, simple installation.
LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
Water flow sensor SEN-HZG1WA Pulse Output 4~45L/min Liquid Switch Flowmeter
- Model: SEN-HZG1WA.
- Use voltage: DC 5V.
- Connect way: G1”, 60*34*34(mm).
- Working voltage range: DC 4.5 ~18V.
- Working current: 15mA.
- Test range: 4~45L/min (m³/h).
- Fit media: water.
- Working pressure: 1.75MPa.
- Outside nominal diameter: G1 (mm).
- Instantaneous flow pulse characteristics: F= [5Q-3]±10%, F means instantaneous pulse value(Hz),Q means instant flow(L/min).
- Insulation resistance = 100MO.
- Electric strength: AC 500V, 50Hz.
- Precision grade: +-10%.
- Working temperature: 60 degree C
- Type: vane-wheel type flowmeter.
YF-S201 ½” Water Flow Sensor
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC
- Max current draw: 15mA @ 5V.
- Output Type: 5V TTL
- Pulses per Litre: 450
- Working Flow Rate: 1 to 30 Liters/Minute
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Durability: minimum 300,000 cycles
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread.
- The simple and compact module.
- Easy to Install.
- High Sealing Performance.
- High-Quality Hall Effect Sensor.
Reviews
There are no reviews yet.