I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Double speed measuring module encoder photoelectric pulse output module
₹180.00 Original price was: ₹180.00.₹150.00Current price is: ₹150.00. inc. GST
- Color: Green + black
- Material: FR4
- Working Voltage: 4.5~5.5V
- Launch Tube Pressure drop: V f=1.6V
- Launch Tube Current: I f<20mA
- Signal Output: A, B two lines
- TT Power Level
- Resolution: 0.01mm
- Measurement Frequency: 100 kHz
- D Type Holes Encoder Diameter: 24mm
- Encoder Resolution: 20 lines
- Speed measuring Sensor configuration: measure line 1 motor speed
Out of stock
This is Double Speed Measuring Module Two Speed Encoder Photoelectric Encoder Pulse Output Module HC – 020K. When combined with a black encoder, the switch output speed measurement module can measure motor speed. The HC-020K module, which has a broad voltage range, high resolution, and fast reaction time, is frequently used in the manufacture of high-precision encoders. This gadget uses a black encoder to measure the rotational speed of the motor (the encoder’s inner diameter is 4mm, therefore it may be used for motor output shafts with 4mm diameter, like the TT motor we matched, yellow shell and white axis).
The HC-020K Speed Encoder is a small module with an encoder disc for measuring motor speed. Furthermore, the module runs on 5V. And shows if there is a gap between the encoder and the reader at a frequency of 100kHz. It may also be used to determine the robot’s location. Although we must be aware that the motor rotation direction cannot be determined, we must always presume that the direction is the same as the ordered direction. There are just three pins on the module for connection, power, ground, and sensor output. To reduce the installed footprint, the right-angle header is mounted backwards.
PIN DESCRIPTION
- 5V – Connects to 5V on MCU
- GND – Connects to the ground on MCU
- OUT – Connects to a digital interrupt input or digital pin on MCU

Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
4*3 MATRIX KEYPAD
- Operating voltage: 12V DC
- The maximum voltage across each button: 24v
- The maximum current across each button: 3mA
- Ultra-thin design
- Adhesive backing provides easy integration
- Easy communication with any microcontroller
- Flexible
- Only 7 microcontroller pins required to access 12 keys
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
4*4 MATRIX KEYPAD
- The maximum current across each button: 3mA
- Easy communication with any microcontroller
- Ultra-thin design
- Adhesive backing provides easy integration
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm

Reviews
There are no reviews yet.