I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-8%
A4988 Stepper Motor
Original price was: ₹175.00.₹160.00Current price is: ₹160.00. inc. GST
DRV8825 Stepper Motor
Original price was: ₹300.00.₹275.00Current price is: ₹275.00. inc. GST
- Operating voltage: 8.2V to 45V
- Continuous current per phase: 1.5 Amp
- Maximum current per phase: 2.2 Amp
- Minimum logic voltage: 2.5V
- Maximum logic voltage: 5.25V
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- The Correct current decay mode (fast decay or slow decay) selected by chopping control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
Description
The DRV8825 stepper motor driver carrier designed as a breakout board based on TI’s DRV8825 micro-stepping bipolar stepper motor driver. It offers a wide range of advantages such as adjustable current limiting, over-temperature and over-current protection, and six microstep resolutions (down to 1/32-step). It operates at a wide operating voltage ranging from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
This module provides a nearly identical pinout and interface to those of the A4988 stepper motor drivers. As a result, used as a higher-performance drop-in replacement for many applications. DRV8825 stepper motor driver is easily controllable with any controller like Arduino, Raspberry Pi, AVR, and many others. Thus simplifies coding and ensures more flexibility in controlling motor.
DRV8825 stepper motor driver uses highly prominent Texas Instruments DRV8825 IC. This stepper motor can be controlled via just 2 pins. In which one for direction and the other for speed and step control. Thus makes it quite easy to control the speed and position of the motor from a microcontroller, Arduino, Raspberry Pi, etc. In case if we want to control a stepper Motor from Arduino, Raspberry Pi, or any other Micro-controller, this DRV8825 stepper motor driver will be a perfect choice. Thus simplify your coding and will give you more flexibility in controlling the stepper motor.
Application
- Printers and scanners
- 3D printers and CNC
- Roboticsufficient additional cooling).
Reviews (0)
Shipping & Delivery
Related products
3.17mm RC Aluminum Bullet Propeller Adapter Holder
- Bore Diameter: 3.7mm (expandable up to 4.1mm).
- Material: Aluminium.
- Colour: Silver.
- Ease of interfacing.
- Rust-free and stain-free aluminum metal construction.
- Used to capture propeller with BLDC motor in quad-copter/multi-rotor/drone.
- High-quality aluminum material.
- Suitable for brushless motors and speed controllers.
- Delicate workmanship.
- High-Quality RC 3.17mm Prop Adaptor For Motor Propeller Plane, Multicopter, Quadcopter
- Dimension: 2.5mm Long x 12mm Diameter
- weight: 4g
A2212 BRUSHLESS DC MOTOR 1400KV
- Operating voltage: 7.2V to 12V
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 1000gms approx.
- Thrust @ 3S with 0945 propeller: 650gms approx.
- Thrust @ 3S with 0845 propeller: 550gms approx.
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
Bullet Connector 3.5MM
- Diameter: 3.5mm
- Length:1.5CM & 1.5CM
- Amperage Rating: 60A -180Amps
- Hook up RC Battery to Electronic
- Hook up Brushless motor to electronic speed control
- These have low resistance and gives the best electric flow
- 5mm gold connectors Male
- 5mm gold connectors Female
- Dimension: 2.7*2.1*3inch
- Weight: 67gm
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
Motor Driver IC – L293D
- Can be used to run Two DC motors with the same IC.
- Speed and Direction control is possible
- Motor voltage Vcc2 (Vs): 4.5V to 36V
- Maximum Peak motor current: 1.2A
- Maximum Continuous Motor Current: 600mA
- Supply Voltage to Vcc1(vss): 4.5V to 7V
- Transition time: 300ns (at 5Vand 24V)
- Automatic Thermal shutdown is available
- Available in 16-pin DIP, TSSOP, SOIC packages
- Featuring Unit rode L293 and L293D
- Wide Supply-Voltage Range: 4.5 V to 36 V
- Separate Input-Logic Supply
- Internal ESD Protection
- Thermal Shutdown
- High-Noise-Immunity Inputs
- Output Current 1 A Per Channel (600 mA for L293D)
- Peak Output Current 2 A Per Channel (1.2 A for L293D)
- Output Clamp Diodes for Inductive Transient Suppression
ULN2003 Driver
- Contains 7 high-voltage and high current Darlington pairs
- Each pair is rated for 50V and 500mA
- Input pins can be triggered by +5V
- All seven Output pins can be connected to gather to drive loads up to (7×500mA) ~3.5A.
- Can be directly controlled by logic devices like Digital Gates PIC etc
- Available in 16-pin DIP, TSSOP, SOIC packages
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
Reviews
There are no reviews yet.