I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
DS1307 64 X 8 Serial Real Time Clock IC
₹55.00 Original price was: ₹55.00.₹45.00Current price is: ₹45.00. inc. GST
- 64 X 8 Serial Real Time Clock
- Supply Voltage range: 4.5V to 5.5V
- Input Logic 1 Min Voltage: 2.2 V
- Input Logic 0 Min Voltage: -0.3V
- Output Logic 0 Max Voltage: 0.4V
- SCL Clock Frequency: 100kHz
- Active Supply Current: 1.5mA
- Rise Time: 1000ns
- Fall Time: 300ns
- Package: DIP-8
DS1307 64 X 8 Serial Real Time Clock IC is an 8 pin device with a full binary-coded decimal (BCD) using 56 bytes of battery-backed SRAM. In this module address and data transferred serially through an I2C, bidirectional bus. The DS1307 operates as a slave device on the I2C bus. The DS1307 RTC module is a low-power clock providing seconds, minutes, hours, day, date, month and year qualified data. It automatically adjusts the end date of each month especially for months with less than 31 days, including the corrections of a leap year.
In the DS1307 RTC module, access obtained by implementing a START condition and providing a device identification code followed by a registered address. Until a STOP condition executed the subsequent registers accessed sequentially. The DS1307 RTC provides a battery back-up function that keeps the clock running even if there is a power failure. RTCs used in a wide range of applications like embedded systems and computer motherboards, etc.
The DS1307 provides an inbuilt power-sense circuit that detects power failures, as a result automatically switches to the backup supply. Timekeeping operation continues even though the module is operating from the backup supply. The DS1307 consists of an external 32.768 kHz crystal. There is no need for any external resistors or capacitors to operate the oscillator.
When VCC falls below 1.25 x VBAT, the device resets the device address counter and terminates access in progress. Inputs to the device will not be recognized at this time to prevent erroneous data from being written to the device from an out-of-tolerance system. Under the condition when VCC falls below VBAT, the device switches into a low current battery-backup mode. As soon as the power-up, the device switches from battery to VCC.

Related products
1/4W 5% Assorted Value Carbon Film Resistor Assortment Kit Set pack electronic diy kit
- 100% brand new and high quality.
- Fine workmanship and long service life.
- 1/4W carbon film resistor package.
- High precision and stability.
- Easy to use.
- Precision: 5%
- Error: 5%
- Values
- 10Ω, 15Ω, 22Ω, 33Ω, 47Ω, 68Ω, 100Ω, 220Ω, 330Ω, 470Ω, 1k, 1k5, 2k2, 3k3, 4k7, 5k6, 6K8, 8K2, 10K, 15K, 22K, 33K, 47K, 56K, 68K, 100K, 150K, 220K, 330K, 470K
- Package included: 150pcs
120pcs 12 value 1uF-470uF Electrolytic Capacitor Kit 1UF 2.2UF 3.3UF 4.7UF 10UF 22UF 33UF 47UF 100UF 220UF
AP Extension pigtail SMA female socket jack to UFL IPX Connector
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
GSM Antenna
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm

Reviews
There are no reviews yet.