I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Flysky CT6B 6 Channel
₹4,850.00 Original price was: ₹4,850.00.₹4,000.00Current price is: ₹4,000.00. inc. GST
- Channels: 6 Channels
- Operating Voltage: 12V DC (1.5AA x 8 Battery).
- Model type: Heli, Airplane, Glider
- RF Power: Less than 20db
- Modulation: GFSK
- Code Type: 2.4Ghz No Interference
- Sensitivity: 1024.
- Bandwidth: 500 kHz.
- Default Operating Mode: Mode 2 (Left-Hand Throttle).
- Low Voltage Warning: LED
- We can programme by PC with the included software.
- Super active and passive anti-jamming capabilities.
- Very low power consumption.
- 4 Types (Airplane, Heli90, Heli120, Heli140).
- DSC Port: Yes
- Charger Port: Yes
- ANT length: 26mm
- Certificate: CE FCC
- Dimension: 190*80*240mm
- Weight: 680g
FlySky CT6B 2.4Ghz 6CH Transmitter with FS-R6B Receiver is a digital proportional radio control system. FlySky CT6B 2.4Ghz 6CH Transmitter with FS-R6B Receiver constitutes a 6 channel 2.4GHz specifically designed and patented by FLYSKY for all the Radio Control models. It offers superior protection and high reliable sensitivity while maintaining low power consumption. This Transmitter is considered to be one of the prominent systems available in the market.
FS-CT6B 6ch 2.4GHz transmitter with FS-R6B Receiver has 0.8W transmitter with a range up to 1km line of sight. . This 6CH transmitter is an entry-level 2.4 GHz radio system that offers high reliability of 2.4 GHz signal technology and provides a receiver with 6 channels. Though CT6B 2.4GHz 6CH transmitter radio is quite expensive compared to others. But it’s value for money. Thus this entry-level 6 channel transmitter is highly recommended using quadcopters and multicopters that require the 6ch operation.
This radio control model consists of two retract switches and proportional flap dials for easy access for channels 5 and 6. 8 x AA Size Batteries or a 12V Power Supply used to power this radio control system. A trainer port is provided to help beginners learn flying. These can be configured by connecting directly to the computer. T6config software is used to configure your radio on a computer. Flysky CT6B 6 Channel digital radio control models are said to be super active and provide passive anti-jamming capabilities. 2.4GHz is considered as the standard of the new generation radio system because it provides numerous advantages. The system’s bandwidth ranges from 2.48GHz to 2.475 GHz.
1 review for Flysky CT6B 6 Channel

Related products
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM
- MAVLink protocol framing status documents.
- Frequency modulation and Spread Spectrum (FHSS).
- Self-adaption to time-division multiplexing.
- Support LBT and AFA.
- Configurable duty cycle.
- Built-in error correcting code(up to 25% data bit error).
- AT command configures data transmission.
- RT command remote control data transmission.
- Interchangeable air and ground 433MHz modules.
- Micro-USB port.
- 6-position Molex connector.
- 250mW maximum output power (adjustable).
- SMA connector.
- 2-way full-duplex communication through adaptive TDM.
- UART interface.
- Transparent serial link.
- Open-source SIK firmware.
- Configurable through *Mission Planner and *APM Planner.
- Featuring a SiLabs Si1000 RF Microcontroller
- Support OTG of Android Cellphone and Compute
- Based on the Hope RF HM-TRP radio Module,
CM8870 ISO2 CMOS Integrated DTMF Receiver IC
ESC 30A BLDC Electronic Speed Controller
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
KK2 1.5 Flight Control
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.

Joel –
Good transmitter and receiver combo, recieved the product in two days and we’ll packed