Showing all 9 results

3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM

  • MAVLink protocol framing status documents.
  • Frequency modulation and Spread Spectrum (FHSS).
  • Self-adaption to time-division multiplexing.
  • Support LBT and AFA.
  • Configurable duty cycle.
  • Built-in error correcting code(up to 25% data bit error).
  • AT command configures data transmission.
  • RT command remote control data transmission.
  • Interchangeable air and ground 433MHz modules.
  • Micro-USB port.
  • 6-position Molex connector.
  • 250mW maximum output power (adjustable).
  • SMA connector.
  • 2-way full-duplex communication through adaptive TDM.
  • UART interface.
  • Transparent serial link.
  • Open-source SIK firmware.
  • Configurable through *Mission Planner and *APM Planner.
  • Featuring a SiLabs Si1000 RF Microcontroller
  • Support OTG of Android Cellphone and Compute
  • Based on the Hope RF HM-TRP radio Module,

433mHz Transmitter Receiver RF Radio Module

250.00
  • Range in open space(Standard Conditions) : 100 Meters
  • RX Receiver Frequency: 433 MHz
  • RX Typical Sensitivity: 105 Dbm
  • RX Supply Current: 3.5 mA
  • RX IF Frequency: 1MHz
  • RX Operating Voltage: 5V
  • TX Frequency Range: 433.92 MHz
  • TX Supply Voltage: 3V ~ 6V
  • TX Output Power: 4 ~ 12 Dbm
  • Low Power Consumption
  • Easy For RF-based Application
  • Complete Radio Transmitter
  • Transmit Range Up To 50m
  • CMOS / TTL Input
  • No Adjustable Components
  • Very Stable Operating Frequency
  • Low Current Consumption (Typ 11mA)
  • Wide Operating Voltage
  • ASK Modulation

FlySky 2.4Ghz 6CH Receiver

  • Item Name: FS-R6B Receiver
  • Brand Name: Flysky
  • Power input: 4.0 -6.5 V DC
  • RF power: less than 20DBm
  • Modulation: GFSK
  • Code type: PCM
  • Sensitivity: 1024
  • PWM channels: 6
  • Protocol: AFHDS
  • Distance: >150m
  • Antenna type: Built-in antenna
  • Low voltage warning: LED
  • Charger port
  • Certificate: CE,FCC,RoHS
  • Dimension: 30*25*8mm
  • Weight: 25g

Flysky CT6B 6 Channel

2,999.00
  • Channels: 6 Channels
  • Operating Voltage: 12V DC (1.5AA x 8 Battery).
  • Model type: Heli, Airplane, Glider
  • RF Power: Less than 20db
  • Modulation: GFSK
  • Code Type: 2.4Ghz No Interference
  • Sensitivity: 1024.
  • Bandwidth: 500 kHz.
  • Default Operating Mode: Mode 2 (Left-Hand Throttle).
  • Low Voltage Warning: LED
  • We can programme by PC with the included software.
  • Super active and passive anti-jamming capabilities.
  • Very low power consumption.
  • 4 Types (Airplane, Heli90, Heli120, Heli140).
  • DSC Port: Yes
  • Charger Port: Yes
  • ANT length: 26mm
  • Certificate: CE FCC
  • Dimension: 190*80*240mm
  • Weight: 680g
 

LOW Cost TX & RX 315MHz

150.00
  • Transmitter Module
    • Operating voltage: 3V to 12V
    • Operating frequency: 433.92MHz; 315MHz
    • Standby current: 0mA
    • Operating current: 20mA to 28mA
    • Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
    • Output power: 16dBm (40mW)
    • Data transfer rate: <10Kbps
    • Modulation mode: OOK (amplitude modulation)
    • Operating temperature: -10℃ to +70℃
    Receiver Module
    • Operating voltage: 5V DC
    • Static current:4mA
    • Receiver frequency: 433.92MHz; 315MHz
    • Sensitivity: -105dB
    • External antenna: 32CM single wire spiral
    • No of pins: 4

Mini SMD NRF24L01 2.4G Wireless Data Transmission Module

150.00
  • Maximum operating speeds up to 2Mbps
  • GFSK modulation efficiency, Anti-interference ability,
  • Built-in hardware CRC error detection, Multipoint communication address control.
  • Low-power 1.9 to 3.6V, only 1uA on Power-down mode
  • Built-in 2.4Ghz antenna
  • Built-in voltage regulator
  • 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
  • Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
  • The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
  • In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
  • Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
  • Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient

NRF24L01 Long Range

375.00
  • Voltage: 3-3.6V (recommended 3.3V) V.
  • Maximum output power: +20dBm.
  • Power-down mode current: 4.2uA.
  • Operating Range: 1Km.
  • Transmission mode current(peak): 115mA
  • Receiver Mode Current(peak): 45mA
  • Power-down mode current: 4.2uA
  • Sensitivity 2Mbps mode in received: -92dBm
  • It uses 2.4GHz global open ISM band, with license free.
  • SPI interface facilitates the communication with MCU I/O port.
  • Support six-channel data reception.
  • 2Mbit/s speed makes high-quality VoIP possible
  • Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
  • Supports 126 RF channels
  • Onboard antenna for optimum performance
  • Standard DIP type pinout for easy Interface through jumper wires or breadboard
  • Small size: 16.5mm*45.5mm.

NRF24L01 Wireless Module

  • Frequency Range: 2.4 GHz ISM Band
  • Maximum Air Data Rate: 2 Mb/s
  • Modulation Format: GFSK
  • Output Power: 0 dBm
  • Operating Supply Voltage: 1.9 V to 3.6 V
  • Operating Current : 13.5mA
  • Current(Standby Mode): 26µA
  • Logic Inputs: 5V Tolerant
  • Communication Range: 800+ m (line of sight)
  • Built-in hardware CRC error detection, Multipoint communication address control.
  • Built-in voltage regulator
  • Wireless transceiver including: Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
  • As the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
  • Built-in 2.4GHz antenna, supports up to six channels of data reception
  • 125 channels, multi-point communication and frequency hopping to meet the communication needs
  • NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
  • Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
  • Dimension: 15 x 29mm

RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]

550.00
  • Operating voltage: 3.6~5.5v ( 5v recommended),
  • Receiver sensitivity as high as -110dbm,
  • Compatible with HT12E and HT12D,
  • Low power and good range.
  • High-frequency stability and low coherence and interference
  • Easy interfacing with the RF modules, using the female headers for placing the modules.
  • Breakout pins for connecting to the microcontroller.
  • DIP Switch for Address Selection (when multiple modules are used at one location)
  • Status LED for valid transmit.
  • Supports both ASK, FSK RF modules
  • Small size, high quality PCB.