I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-12%Sold out
Tilt Sensor / Vibration Sensor
Original price was: ₹250.00.₹200.00Current price is: ₹200.00.
Load Cell CZL 601 40KG
Original price was: ₹500.00.₹450.00Current price is: ₹450.00. inc. GST
GPS Modem with External Antenna
Original price was: ₹1,700.00.₹1,500.00Current price is: ₹1,500.00.
- SiRF Star IVâ„¢, GSD4e ROM version
- Tracking sensitivity -163dBm, autonomous Acquisition sensitivity -148dBm
- TTL interface output
- 48 track verification channels
- Power supply 3.3 voltage
- SMT type with stamp holes
- Small form factor with embedded SiRF star iv technology
- Removes in-band jumbers up to 80dB-Hz, track up to 8CW jammers
- Excellent sensitivity for urban canyon and foliage environments.
Out of stock
Description
The GPS Modem with External Antenna designed as a complete GPS engine module. It features super sensitivity, ultra-low power, and a small form factor makes it the best choice to be embedded in various devices. This GPS module powered by the latest SiRF Star IVâ„¢, GSD4e ROM version chip, and RoyalTek proprietary navigation technology. Â This GPS Receiver designed with an External Active Antenna is quite easy to use with PC or MCU.
The GPS signal applied to the antenna input of the module. It consists of a complete serial data message with position, velocity, and time information presented at the serial interface with NMEA protocol or custom protocol. Due to the high tracking sensitivity of –163dBm, and autonomous Acquisition sensitivity -148dBm. Thus the module helps to extend positioning coverage into urban areas and dense foliage environments where the GPS was unable to reach before. Moreover, the small form factor and low power consumption make the module installation quite easier and simpler. Thus it can be easily integrated into portable devices like PNDs, mobile phones, cameras, and vehicle navigation systems. Moreover, it supports Dual Power Source, Serial, and TTL output Free GPS Active Antenna.
Applications
- LBS (Location-Based Service)
- PND (Portable Navigation Device)
- Vehicle navigation system
- Mobile phone
Reviews (0)
Shipping & Delivery
Related products
Antenna GSM-2DBI (Spring)
- Gain: 2dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
- Package includes:
GPS Ublox Neo 6M TTL
- Supply voltage: 3.3 V
- 5Hz position update rate
- Operating temperature range: -40 TO 85°C
- UART TTL socket
- EEPROM to save configuration settings
- Rechargeable battery for Backup
- The cold start time of 38 s and Hot start time of 1 s
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
- -162 dBm tracking sensitivity
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
- Separated 18X18mm GPS antenna
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
NRF24L01 Long Range
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km.
- Transmission mode current(peak): 115mA
- Receiver Mode Current(peak): 45mA
- Power-down mode current: 4.2uA
- Sensitivity 2Mbps mode in received: -92dBm
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
- Support six-channel data reception.
- 2Mbit/s speed makes high-quality VoIP possible
- Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
- Supports 126 RF channels
- Onboard antenna for optimum performance
- Standard DIP type pinout for easy Interface through jumper wires or breadboard
- Small size: 16.5mm*45.5mm.
![RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]](https://www.mathaelectronics.com/wp-content/uploads/2021/02/ROBOSOFT-LABS-RF-RX-TX-ENCODER-DECODER-MODULE-BOARD-SKURL5037-228x228-1.jpg)
RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]
- Operating voltage: 3.6~5.5v ( 5v recommended),
- Receiver sensitivity as high as -110dbm,
- Compatible with HT12E and HT12D,
- Low power and good range.
- High-frequency stability and low coherence and interference
- Easy interfacing with the RF modules, using the female headers for placing the modules.
- Breakout pins for connecting to the microcontroller.
- DIP Switch for Address Selection (when multiple modules are used at one location)
- Status LED for valid transmit.
- Supports both ASK, FSK RF modules
- Small size, high quality PCB.
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4
Ublox NEO-M8N GPS Module with Compass for APM with extra connector for Pixhawk
- Ready to Connect to All APM FC with 5-pin connector Attached
- Receiver type 72-channel M8 engine
- Galileo-ready E1B/C (NEO-M8N)
- update rate1 Single GNSS: up to 18 HZ
- Position accuracy 22.0 m CEP
- Acquisition2 Cold starts: 26 s
- Sensitivity2 Tracking & Nav: –167 dBm
- On-board Compass
- Dimensions: Outer diameter 54mm
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Assistance AssistNow GNSS Online.
- Assist Now GNSS Offline (up to 35 days)3.
- Assist Now Autonomous (up to 6 days).
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q).
- Crystal (NEO-M8M).
- RTC crystal Built-In.
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
- Lowest noise figure (NEO-M8N/Q).
- Anti-jamming Active CW detection and removal.
- Extra onboard SAW bandpass filter (NEO-M8N/Q).
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
- Supported antennas Active and passive.
- Odometer Travelled distance.
- Data-logger For position, velocity, and time (NEO-M8N).
- Weight 33gm
Reviews
There are no reviews yet.