I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
ISD1760 MODULE (75 sec)
₹549.00 Original price was: ₹549.00.₹499.00Current price is: ₹499.00. inc. GST
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm
Â
ISD1760 is a playback module consisting of an onboard microphone and a voice recording IC with 75 sec of audio playback. This module is is compatible with all ISD1760 series families that can be applied to all series chips, with simple and full functional characteristics. ISD1760 Module is defined as highly integrated and high-performance chips with multi-segment recording at an adjustable sampling rate from 4k to 12k at a varying power supply of 2.4V to 5.5V. The LED indication is provided every few seconds to alert the user for new recordings. Apart from it, there are 4 modes of sound to prompt user operating results.ie start reading, stop reading, erase, and erase all next to one, and so on.
Flash chip is used to store data without any compression. In SPI mode, the user function more on-chip address and power are less consumed by automatically entering to power-down mode. Analog channel configuration register used for reading and writing memory addresses on the playback. Moreover, the recording data is stored without any compression in the FLASH chip. Hence offers better sound quality and power storage.
This playback module chip consists of two independent audio signal input channels, microphone input, and analogue signal inputs. In the independent key mode, as soon as the operation is completed, a functional chip automatically enters the power-down mode to reduce power consumption. And also the 2.54mm spaced male pin headers in the module allow easy interfacing with the microcontroller.

Related products
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
DIGITAL POWER AMPLIFIER BOARD MODULE 35W
Finger Print Module Scanner – TTL (GT-521F52)
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 3,000 unique fingerprints.
- Wake up on Finger Function.
- Works well with dry, moist or rough fingerprints.
- Anti-scratch with surface high hardness ≧
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
Finger print Scanner Module – TTL (GT-521F32)
- Operating Voltage: 3.3V to 6V DC
- Simple UART & USB communication protocol.
- Complies with USB 2.0 full-speed specification.
- Ultra-thin optical sensor.
- Finger window: 12.9 x 16.9 mm.
- Image Size: 258 x 202 Pixels.
- Resolution 450 dpi.
- Capable of 360° recognition.
- Storage for 200 unique fingerprints.
- False Acceptance Rate (FAR): <0.001%
- False Rejection Rate (FRR): <0.01%
- Wake up on Finger Function.
- CPU: ARM Cortex M3 Core MCU).
- Ultra-thin Optical Sensor.
- Works well with dry, moist or rough fingerprints
- Anti-scratch with surface high hardness ≧5
- 1:1 verification, 1:N identification.
- High accuracy and high-speed fingerprint identification technology.
- External UART-to-USB converter required (TX & RX levels: 3.3V).
Fingerprint Scanner TTL GT511C3 – 3.3V to 6V
- Model: GT-511C3
- Operating Voltage(VDC): 3 to 6
- CPU: ARM Cortex M3 Core (Holtek HT 32F2755)
- Sensors: Optical
- Image Size: 202 x 258 Pixel
- Resolution: 450 DPi
- Effective Scanning Area(mm): 20 x 16
- False Acceptance Rate (FAR): 0.001%
- False Rejection Rate(FRR): < 0.1%
- Operating Temperature : -20°C ~ +60°C
- Default Baud Rate: 9600bps
- High-Speed, High-Accuracy Fingerprint Identification using the Smack Finger 3.0 Algorithm
- Read and Write Fingerprint Templates and Databases
- Simple UART protocol (Default 9600 baud)
- Capable of 1:1 Verification and 1:N Identification
- High-accuracy & high-speed fingerprint identification technology.
- Works well with dry, moist, or rough fingerprints.
- 200 fingerprints storage.
- Easy one-touch enrolment.
- Dimensions(mm): 37 x 17 x 9.5
- Weight: 6gm

Reviews
There are no reviews yet.