I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-13%
ISD1760 MODULE (75 sec)
Original price was: ₹549.00.₹499.00Current price is: ₹499.00. inc. GST
L298N MOTOR DRIVER
Original price was: ₹300.00.₹225.00Current price is: ₹225.00. inc. GST
ISD1820 MODULE (10 SEC)
Original price was: ₹400.00.₹350.00Current price is: ₹350.00. inc. GST
- Operating voltage: 2.6v to 5v
- Record and playback up to 10 sec
- Push-button and microcontroller controllable AGC circuit added tom increase audio playback volume
- Recording time: 8- 20 sec
- Built-in microphone
- On-chip 8-ohm speaker driver
- High quality, natural voice restored
- Available single-chip control audio recording control mode: the key to control or microcontroller, IO has drawn the line of control
- Can be used as propaganda module
- Auto power down mode
- Duration and sample rate can be extended to 20 sec by varying resistance
- Dimension: 43*34*11mm
Description
ISD1820 is a single-chip voice message recording IC for single message recording and playback. It allows to record 10 sec of audio and play it back under microcontroller or by manual mode. As it consists of an inbuilt microcontroller, a message up to 10 sec long can be recorded. By connecting a resistor, these 10 secs can be extended to 20 sec. It is a non-volatile module, hence can be recorded up to 100000 times and can be stored without power. An 8-ohm speaker can be driven using the small inbuilt audio amplifier in the module.
ISD1820 chip is a resistor-controlled oscillator input (ROSC) in which sampling rate and maximum duration of audio can be controlled by placing a resistor between ROSC pin and GND, this sets oscillator frequency. The audio play volume of this module can be increased by adding AGC input to the LED output pin.
Reviews (0)
Shipping & Delivery
Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
ACTIVE BUZZER ALARM
- Operating voltage: 3.3V to 5V
- The Transistor driver module uses S8550/9012
- Wire length: 20.5cm
- Easy installation by the fixed bolt hole
- 3 pin TTL cable
- An active buzzer with a concussion internal source is called to be energized
- The program easy to control-SCM high low sound
- When input I/O input is low level, the buzzer sounds
- 28*13.29*11.5mm
ADXL345
- Supply voltage: 3.3V/5V
- Communication type: I2C/SPI
- Sensing range: +/-2G to +/-16G
- Sensitivity
- X: 28.6 LSB/G
- Y: 31.2 LSB/G
- Z:34.5 LSB/g
- On-board LDO voltage regulator
- Resolution: 13 bit
- Single tap/double-tap detection
- Embedded memory management system with FIFO
- 10000g shock survival
- Low power consumption as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical)
- 3-axis MEMS accelerometer
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DS3231 RTC MODULE
- Operating voltage of DS3231: 2.3 v to 5.5v
- 400Khz I2C interface
- Automatic power failure battery switch circuitry
- RTC counts seconds, minutes, hours, and year
- High precision clock chip DS3231
- Programmable square-wave output
- Chip temperature sensor accuracy:+/_3 degree Celsius
- Memory chip: AT24C32 with 32K storage capacity
- CR2032 battery backup with a high life span
- Low power consumption
- Register for ageing trim
- Dimension: 38mm*22mm*14mm
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm
Reviews
There are no reviews yet.