I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
₹800.00 Original price was: ₹800.00.₹750.00Current price is: ₹750.00. inc. GST
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
Ra-02 SX1278 was designed as a wireless transmission module based on SEMTECH’s SX1278 wireless transceiver. It Utilizes the advantages of advanced LoRa spread spectrum technology, offering a communication distance of 10,000 meters. It provides a strong ability of anti-jamming and has the function of air wake-up Consumption. The SX1278 RF module is widely used for long-range spread spectrum communication. And can also resist Minimizing current consumption. The SX1278 offers a high sensitivity of -148 dBm with an influence output of +20 dBm. And an extended transmission distance and high reliability. At a similar time, compared with the normal modulation technology, LoRa â„¢ modulation technology has obvious advantages in anti-blocking and selection, Thus solving the matter that the normal design scheme. Which can’t consider the distance, interference and power consumption at an equivalent time.
It often covers thousands of people in the district environment, particularly suitable for meter reading, smart home, burglar alarm equipment. This product was designed based on the WIFI Kit 32 added SX1278 chip, i.e. LoRa remote modem, 433MHz frequency, about -148dBm high sensitivity, +20 dBm power output. And also offers high reliability, transmission distance (measured open area communication distance 2.6Km).

Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
DS3231 RTC MODULE
- Operating voltage of DS3231: 2.3 v to 5.5v
- 400Khz I2C interface
- Automatic power failure battery switch circuitry
- RTC counts seconds, minutes, hours, and year
- High precision clock chip DS3231
- Programmable square-wave output
- Chip temperature sensor accuracy:+/_3 degree Celsius
- Memory chip: AT24C32 with 32K storage capacity
- CR2032 battery backup with a high life span
- Low power consumption
- Register for ageing trim
- Dimension: 38mm*22mm*14mm
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)
Wemos D1 WiFi Esp8266 Development Board Uno Compatible Program
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
- On-Board Switching Power Supply:
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
XBee Module S2C XB24CZ7WIT-004
- Protocol: ZigBee®
- Transceiver chipset: Silicon Labs EM357 SoC
- RF Standard: 802.15.4
- Frequency (ISM Band): 2.4GHz
- Digital I/O: 15
- ADC Channels: (4) 10-bit ADC inputs
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
- Encryption: 128-bit AES
- Voltage requirements: 2.1 to 3.6 VDC
- Current requirements: ~33 mA @ 3.3VDC (transmit), ~28 mA @ 3.3VDC (receive), <1 uA @25ºC (sleep)
- Migratable to Digi Mesh and ZigBee PRO protocols
- Configuration Method: API or AT commands, local or over-the-air (OTA)
- Communication: CMOS UART / SPI
- Dimensions: 27.61 x 24.38 x 4.06 mm
- Operating temperature range: -40 to +85 °C
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
Xbee Module S2C XBP24CZ7UIT-004
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA
- Current Transmitting: 120mA
- Mounting Type Through Hole
- Operating Temperature: -40°C ~ 85°C

Reviews
There are no reviews yet.