I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-17%
NODEMCU ESP8266-12 USB CH340
Original price was: ₹450.00.₹400.00Current price is: ₹400.00. inc. GST
434MHz/315Mz TX & RX
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
NRF24L01 Long Range
Original price was: ₹450.00.₹375.00Current price is: ₹375.00. inc. GST
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km.
- Transmission mode current(peak): 115mA
- Receiver Mode Current(peak): 45mA
- Power-down mode current: 4.2uA
- Sensitivity 2Mbps mode in received: -92dBm
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
- Support six-channel data reception.
- 2Mbit/s speed makes high-quality VoIP possible
- Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
- Supports 126 RF channels
- Onboard antenna for optimum performance
- Standard DIP type pinout for easy Interface through jumper wires or breadboard
- Small size: 16.5mm*45.5mm.
Description
The NRF24L01 module based on the latest RF modules uses the 2.4GHz transceiver from Nordic Semiconductor, the NRF24L01+. This module comes with the 2.4G antenna (2DB), with a 250Kbps transmission rate on open-air. And operated at a communication distance of 800-1K meters. This module widely used for long-distance communication. NRF24L01 module board features a reverse polarized SMA connector to achieve maximum RF range. Moreover, there is PA and LNA circuit on board, with the external antenna allows reaching long-distance than the one without these parts. This wireless Transceiver module is an ideal solution to design a wireless communication system at a low cost.
This module can be easily added with MCU/ARM/PIC/AVR/STM32 system. NRF24L01 module is a high power, long-range, and easy to use RF wireless transceiver module with a high on-air data rate of up to 1 – 2 Mbps. It comes with an external antenna and can work in ranges up to 1100 meters (requires a stable power supply, low data rate, and low surrounding interference with the line of sight). Hence this is one of the cheapest and easiest modules for wireless communications using Arduino, Raspberry Pi, and other microcontrollers. Moreover, this module supports a standard SPI interface, in which we can directly interface this module to any microcontroller. Thereby eliminating the need for an external circuit.
Applications:
- Â Wireless peripherals, remote control systems such as RC vehicles and consumer remote electronics
- wireless voice transmissions such as VoIP, wireless sensor networks, wireless networks, home, and commercial automation.
Reviews (0)
Shipping & Delivery
Related products
3DR Single TTL MINI Radio Telemetry 433MHz 250mW for PIXHAWK and APM
- MAVLink protocol framing status documents.
- Frequency modulation and Spread Spectrum (FHSS).
- Self-adaption to time-division multiplexing.
- Support LBT and AFA.
- Configurable duty cycle.
- Built-in error correcting code(up to 25% data bit error).
- AT command configures data transmission.
- RT command remote control data transmission.
- Interchangeable air and ground 433MHz modules.
- Micro-USB port.
- 6-position Molex connector.
- 250mW maximum output power (adjustable).
- SMA connector.
- 2-way full-duplex communication through adaptive TDM.
- UART interface.
- Transparent serial link.
- Open-source SIK firmware.
- Configurable through *Mission Planner and *APM Planner.
- Featuring a SiLabs Si1000 RF Microcontroller
- Support OTG of Android Cellphone and Compute
- Based on the Hope RF HM-TRP radio Module,
ENC28J60 ETHERNET MODULE
- ENC28J6 Ethernet chips, SOP28 package
- Operating voltage: 3.1V to 3.6V (3.3 V typical)
- Operating temperature: -40 degree to +85 degree Celsius
- IEEE 802.3 compatible Ethernet controller
- Buffer size: 8Kb
- Supports full and half-duplex mode
- SPI interface with a clock speeds up to 20MHz
- Programmable automatic rejection of erroneous packets
- Programmable automatic retransmit on a collision
- Programmable padding and CRC generation
- 25 MHz crystal oscillator
- Clock out the pin with a programmable presale
- Ethernet LAN module for Arduino/AVR/LPC/STM3
- 5V tolerant inputs
- SPI interface
- Led power indicator
- Dimension: 58*34*17mm
ESP8266-12E 10A 220V NETWORK RELAY WIFI MODULE INPUT DC 7V-30V
- Input voltage: DC 7V-30V
- Relay voltage: 220V
- Relay current: 10A
- ISM: 2.4GHz
- PA: +25dBm
- Input over-voltage protection
- Input overcurrent protection
- ESP8266 WIFI module with 4 layered board design
- LED indicator for input status and output status
- 220V 10A relay, normally opened, and one normally closed
- Optocoupler isolation input, TVS input protection
- Access server control via HTTP protocol by TCP client mode, high current terminals
- Dimension: 65*40*18mm
Mega R3 +WiFi ATmega2560+ESP8266 Module CH340G Compatible For Arduino Mega
- Microcontroller:ATmega2560
- IC Wi-Fi : ESP8266
- USB-TTL converter: CH340G
- Power Out: 5V-800mA
- Power Input USB: 5V (500mA max.)
- Power Input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- Wi-Fi 802.11 b/g/n 2.4 GHz
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type: SerialOTA
- Operating temperature:−40С°/+125С°
- Build in external antenna
- Dimensions:53.361×101.86mm
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4
UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno
- Microcontroller: ATmega328IC
- Wi-Fi: ESP8266
- USB-TTL converter: CH340G
- Power Output: 5V-800mA
- Power input USB: 5V (500mA max.)
- Power input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- WiFi: 802.11 b/g/n 2.4 GHz
- USB type: Micro USB
- USB Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O Pins: 14
- Analog I/O pins: 6
- Memory Size: 32Mb
- Interface Type: serial
- Operating temperature: −40С°/+125С°
- Dimensions (L×W)mm: 53.34×68.58
Reviews
There are no reviews yet.