I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-42%
ADC0808 8-Bit A/D Converter with 8-Channel Multiplexer IC DIP-28 Package
Original price was: ₹180.00.₹140.00Current price is: ₹140.00. inc. GST
PCF8583 IC
Original price was: ₹100.00.₹65.00Current price is: ₹65.00. inc. GST
PCF8582E-2 IC DIP-8
Original price was: ₹60.00.₹35.00Current price is: ₹35.00. inc. GST
- Low power CMOS
- Non-volatile storage of 2 kbits organized as 256 × 8-bitÂ
- Â Single supply with full operation down to 2.5 VÂ
- Â On-chip voltage multiplierÂ
- Â Serial input/output I2C-busÂ
- Write operations:Â
- Â Â Â Â Â Â Â Â Â Â Â Â Â –Â byte write modeÂ
                          – 8-byte page write mode (minimizes total write time per byte)
- Â Read operations:Â
                         – sequential readÂ
                         – random readÂ
- Â Internal timer for writing (no external components)Â
- Â Internal power-on resetÂ
- Â 0 kHz to 100 kHz clock frequency
- High reliability by using a redundant storage code
Description
The PCF8582 is a 256×8 CMOS EEPROM with an I2C interface. It comes in a range of plastic 8- and 16-pin units. The 16-pin Dual In-Line package is utilized in this specific arrangement. A 128×8 CMOS EEPROM, PCF8581. Philips television sets that utilize I2C EEPROMs can have their default setup parameters programmed with this Gang Programmer. In addition to demonstrating how to build an I2C interfaced programmer, the design is offered here as an illustration of how to use the 87C751 I2C interface. The data is copied into ten slave EEPROMs by the programmer after being read from a source EEPROM.
The programmer is powered by a 9V @ 300mA wall-mounted source. On the board, there is a 5V regulator. A yellow LED is used to show that the board has received power. There are red LEDs at each socket to signal a failure in the programming procedure for that IC, and green and pink LEDs to indicate the status of the programming operation. If everything goes according to plan, a buzzer will sound and a green LED will show that the programming procedure was successful. If there are any EEPROM faults, the pink LED will illuminate, and the relevant red LED will flash to show which IC is malfunctioning. The I2C communication link has malfunctioned if the pink LED is on but none of the red LEDs are lit.
Reviews (0)
Shipping & Delivery
Related products
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm
Reviews
There are no reviews yet.