I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Sold out
Back to products
PR53 215mm Trapezoidal Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
PR34 2004 LCD Display Smart Controller W or Adapter for RAMPS1.4 Reprap 3D Printer
- RAMPS 1.4 2004 LCD Display intelligent controller.
- LED background light control circuit, a small function of the intelligent controller,
- With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do the long or short form of the adjustment TRIMM R4100K from 10 seconds to 2 minutes.
- Plug and play on the RAMPS, but need to modify the firmware to support.
- The product comes encoder parameter adjustment can be achieved, and the file selection print.
- With an SD card base on the back, put slicing file into the SD card and select the file on the LCD, then can be printing.
Description
The PR34 2004 LCD Display Smart Controller W or Adapter for RAMPS1.4 Reprap 3D Printer designed with an SD-Card reader, a rotary encoder, and a 2004 LCD display. This PR34 2004 LCD Display can be easily connect it to your RAMPS board using the “smart adapter”. After connecting this controller panel to your RAMPS, there is no need to use pc anymore. The 2004 LCD Smart Controller supplies power for your SD card. Moreover, all functions like calibration, axes movements performed by just using the rotary encoder on the Smart Controller. Thus the 3D designs printed without PC, just with a g-code design stored on the SD card.
This 2004 LCD display is 20 Character x 4 Line LCD display. Using the “smart adapter” included in the module, it can be easily connected to the Ramps board. LCD2004 LCD Display provides a simple and cost-effective solution for adding a 20×4 White on RGB Liquid Crystal Display into your project. And also display comes with 20 characters by 4 line display has a very clear and high contrast white text upon a blue background/backlight.
In this LCD controller, we can turn on the light time to do the long or short form of the adjustment TRIMM R4100K from 10 seconds to 2 minutes. And also the SD card base on the back put the slicing file into the SD card and select the file on the LCD, thus printing can be processed.
Reviews (0)
Shipping & Delivery
Related products
16*1 GREEN (LCD DISPLAY MODULE)
- Operating voltage: 5V
- Display format: 16 characters * 1 line
- Display mode: STN or FSTN
- Dot-matrix: 5*8 dots
- Character size: 3.07 * 6.56mm
- Character pitch: 77 * 6.56mm
- LCD driver IC: ST7066U
- 1/16 duty cycle
- Polarizer mode: Transmissive
- Each character build by 5*8 pixels
- Works on both 8-bit parallel interface
- Operating temperature: -20 degree to 70 degree Celsius
- Low Current consumption
- Alphanumeric display
- Dimension: 80*36*13.2mm
- Compact size and lightweight
16*2 ORANGE (LCD DISPLAY MODULE)
- Input voltage: 4.7V TO 5.3V
- Operating voltage: 5V
- Current consumption is 1mA without backlight
- Consist of 2 rows and each row can print 16 characters
- Can display alphabets and numbers, i.e. alphanumeric
- Viewing area: 99*24mm
- Character size: 5.2*9.55mm
- Each character build by5*8 pixels
- Works on both 8 bit and 4 bit
- Used in industrial applications such as audio, automotive control panels, medical devices, and home automation products, etc.
- Operating temperature:0 degree to 50 degree Celsius
- Storage temperature: -10 degrees to 50 degree Celsius
- 1/16 duty cycle
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
NEMA 23 18.9 kg-cm
- Step Angle : 1.8 °
- Holding Torque : 18.9 kg-cm
- Operating Voltage : 3.2 Volts
- Supply Current (A) : 2.8 A/Phase
- No. of Leads : 4
- Inductance: 3.6 mH/Phase
- Resistance : 1.13 O/Phase
- Rotor Inertia : 480 gm-cm2
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Shaft Diameter (mm) : 6.35
- Shaft Length (mm) : 20.6
- Cable Length: 30 CM
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor Nema 23 kg 7.2 kg Dual shaft
- Rated Voltage: 6.6 V
- Current/ phase: 1A
- Resistance/ phase: 6.6ohms
- Inductance/ phase: 8.2 mH
- Holding Torque: 7.2 kg-cm
- of Leads - 6
- Rotor Inertia - 275
- Weight: 0.65kg
- Detent Torque: 0.36 kg-cm
- Step Angle - 1.8°
- Step Angle Accuracy - ±5% (full step, no load)
- Resistance Accuracy - ±10%
- Inductance Accuracy - ±20%
- Frame Size (mm) - 57x57
- Shaft Length (mm) - 20.6
- Shaft Diameter (mm) - 6.35
- Comparably more powerful than NEMA17 motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
TEVO Tarantula I3 Aluminium Extrusion 3D Printer kit
- Layer resolution of 50 microns.
- MAX Printing Speed: 150 mm/s.
- Build size: 200X 200 X 200mm.
- Full Metal Bowden Extruder.
- Material type: PLA, ABS, PETG, Wood, PVA and Flexible Filaments (With Pro Metal Extruder).
- Material specifications 1.75mm in diameter.
- Positioning accuracy: Z 0.04mm, XY 0.012mm.
- Printing Color: Single color.
- Nozzle diameter: 0.4mm.
- Recommended extruder temperature: 210°C (the maximum can be set to 260°C).
- Heating plate temperature: 60-120°C (proper winter warming and summer appropriate cooling).
- Best ambient temperature: +/-25°C.
- Power requirements: 220V, 250W, 50Hz, 0.89A.
- Connection: TF card or USB.
- The file print format: STL, G-Code.
- Compatibility: Windows, Linux, Mac.
- CE, FCC specifications: CE, FC, ROHS.
- No Printed Parts.
- Easy Assembling.
- High Performance.
- 2020 and 2040 Aluminium Frames.
- Equipment size: 430 X 440 X400mm.
- Package size: 440X 340X 190m.
- Device weight: 7.5kg.
Waveshare 5inch HDMI LCD (B) 800×480
- 800x480 high hardware resolution
- Resistive touch control
- Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
- When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
- When working as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free
- The backlight can be turned off to lower power consumption
- 5mm audio jack speaker provided and supports HDMI audio output
- Supports popular game consoles like Microsoft XBOX360 Sony PS4 and Nintendo Switch etc.
- Multi languages OSD menu for power management brightness/contrast adjustment etc.
- Also supports VGA input(specific cable is required and should be purchased separately)
- Dimensions:18 x 10 x 9 cm
- Weight: 200 Grams
Reviews
There are no reviews yet.