I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Super Mini Elm327 V2.1 Bluetooth Obd2 OBD-Ii Car Auto Diagnostic Scanner Android
₹1,000.00 Original price was: ₹1,000.00.₹950.00Current price is: ₹950.00. inc. GST
- Model Name: ELM327 OBD2 Bluetooth
- Type: code readers & scan tools
- Output protocol: Bluetooth
- Material: plastic
- Voltage: 12V
- Current: 45mA
- Wave frequency: 38400Hz
- Applicable scope: 5-10m / 16.4-32.8ft
- Item size: 49*26*30mm
- Support OBDII Protocols: SAE J1850 PWM (41.6 kbaud), SAE J1850 VPW (10.4 kbaud), SAE J1939, J1979
ELM327 OBD2 V2.1 Bluetooth Interface Auto Car Diagnostic Scanner designed an on-Board Diagnostics. In an automotive context, OBD is a generic term that refers to a vehicle’s self-diagnostic and reporting capability. OBD systems provide the vehicle owner or a repair technician access to the state of health information for various vehicle sub-systems.
The amount of diagnostic information available via OBD has varied widely since the introduction within the early 1980s of onboard vehicle computers, which made OBD possible. Early instances of OBD would simply illuminate a malfunction indicator light, or MIL, if any error or issue was detected. But it does not provide any information on the character of the matter.
Modern OBD implementations make use of a uniform digital communications port to supply real-time data additionally to a uniform series of diagnostic trouble codes, or DTCs. As a result, permits one to rapidly identify and remedy malfunctions within the vehicle. ELM327 Bluetooth CAN-BUS scan tool supports OBD-II protocols. it’s wont to read & diagnose trouble codes, clear trouble codes and detect fuel pressure then on. The Elm327-Bluetooth adapter also gives you the chance to “spy” on your car wirelessly. By Converting PC, PDA, Mobile to a diagnostic tool and thus monitor all critical information of the car’s ECU.
The Elm327-Bluetooth is an adapter that connects to the car’s network then creates a virtual cable between the adapter and therefore the PC that it’s connected to. Moreover, with the assistance of varied open-source application for the Elm327, you’ll have a digital gauge or a complicated diagnostic system and a strong performance measurement toll in your screen.
- Engine RPM
- Calculated Load Value
- Coolant Temperature
- Fuel System Status
- Vehicle Speed
- Short Term Fuel Trim
- Long Term Fuel Trim
- Intake Manifold Pressure
- Timing Advance
- Intake Air Temperature
- Air Flow Rate
- Absolute Throttle Position
- Oxygen sensor voltages/associated short term fuel trims
- Fuel System status
- Fuel Pressure

Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
4*4 MATRIX KEYPAD
- The maximum current across each button: 3mA
- Easy communication with any microcontroller
- Ultra-thin design
- Adhesive backing provides easy integration
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
AC-DC Power Module HLK-PM01 230V to 5V /3W
- Meet UL, CE requirements
- Rated input voltage: AC 100V -230V
- Maximum input voltage: <270V AC
- Voltage Regulation: ±0.2%
- Load Regulation: ±0.5%
- High efficiency, high power density
- Ultra-thin and small module
- Low ripple and low noise
- Output overload and short circuit protection
- 100% load ageing and testing
- The product is designed to meet the requirements of the EMC and Safety Test
- Low power consumption, environmental protection, no-load loss <0.1W
- High efficiency, high power density
- Working temperature: – 20 degrees to +60 degrees Celsius
- Storage temperature: + 80-40 -degree
- Relative humidity: 5-95%
- Cooling way: Natural cooling
- Atmospheric pressure: 80-106Kpa
- Weight: 21g
- Size: 38x23x18mm
DS3231 RTC MODULE
- Operating voltage of DS3231: 2.3 v to 5.5v
- 400Khz I2C interface
- Automatic power failure battery switch circuitry
- RTC counts seconds, minutes, hours, and year
- High precision clock chip DS3231
- Programmable square-wave output
- Chip temperature sensor accuracy:+/_3 degree Celsius
- Memory chip: AT24C32 with 32K storage capacity
- CR2032 battery backup with a high life span
- Low power consumption
- Register for ageing trim
- Dimension: 38mm*22mm*14mm
ENC28J60 ETHERNET MODULE
- ENC28J6 Ethernet chips, SOP28 package
- Operating voltage: 3.1V to 3.6V (3.3 V typical)
- Operating temperature: -40 degree to +85 degree Celsius
- IEEE 802.3 compatible Ethernet controller
- Buffer size: 8Kb
- Supports full and half-duplex mode
- SPI interface with a clock speeds up to 20MHz
- Programmable automatic rejection of erroneous packets
- Programmable automatic retransmit on a collision
- Programmable padding and CRC generation
- 25 MHz crystal oscillator
- Clock out the pin with a programmable presale
- Ethernet LAN module for Arduino/AVR/LPC/STM3
- 5V tolerant inputs
- SPI interface
- Led power indicator
- Dimension: 58*34*17mm
I2C MODULE WITH 16*2 CHARACTER LCD
- Supply voltage: 5V
- Display mode: STN
- Display format: 16*2
- Input data: 4 bit or 8 bit (for LCD)
- I2C address: 0x20~0x27 (original address is 0x20,we can change it ourselves)
- Compatible with multiple communication logic levels: 2.8~5VDC
- Compatible for 16*2 LCD
- Serial I2C control of LCD display using PCF8574
- Allow data display via only 2 wires.
- Backlight and contrast adjustment by the potentiometer
- Supports 7 ASCII fonts, 5 graphic functions
- Supports 128 level backlight lightness adjustment.
- Support 64 level screen contrast adjustment
- Supports device address modification
- Dimension: 10*4*5cm
- Size: 150gm
ISD1760 MODULE (75 sec)
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm

Reviews
There are no reviews yet.