I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
TEA1062A Low Voltage Transmission Circuits with Dialer Interface IC
₹30.00 Original price was: ₹30.00.₹20.00Current price is: ₹20.00. inc. GST
- Low Voltage Transmission Circuits with Dialer Interface
- Line Voltage: 4V
- Internal Supply Current Max: 1.35mA
- Microphone Amplifier Voltage Gain: 52dB
- Receiving Amplifier Voltage Gain: 31dB
- Common Mode Rejection Ratio (Mic): 82dB
- Package: DIP-16
aria-labelledby=”at-3a0221cb-4417-4921-a94d-04561afb5bc2″>
 </div>
The TEA1062A is an integrated circuit that performs all voice and line interface tasks in fully electronic telephone systems. These gadgets are designed to transition between dialling and speaking via electrical switching. To allow for the usage of several telephone sets linked in parallel, the ICs function at line voltages as low as 1.6 V DC (with decreased performance.
The telephone line provides the power necessary for the IC and its peripheral circuitry. The IC regulates the supply voltage, which is obtained from the line through a dropping resistor. External circuits, such as dialling and control circuits, are likewise powered by the supply voltage VCC. A capacitor between VCC and VEE is used to decouple the supply voltage. A capacitor between REG and VEE decouples the internal voltage regulator. Meanwhile, the exchange supply voltage Vexch, the feeding bridge resistance Rexch, and the DC resistance of the telephone line Rline define the DC current flowing into the set.
A 3.6 k resistor connected between STAB and VEE controls the amount of the circuit’s inbuilt current stabiliser (see Fig.9). The surplus current is shunted to VEE through LN when the line current (Iline) is more than 0.5 mA larger than the total of the IC supply current (ICC) and the current drawn by peripheral circuitry linked to VCC (Ip). Calculate the regulated voltage on the line terminal (VLN) as follows:
VLN = Vref + ISLPE × R9
VLN = Vref + {(Iline − ICC − 0.5 × 10−3 A) − Ip} × R9
Vref is an internally generated temperature compensated reference voltage of 3.7 V and R9 is an external resistor connected between SLPE and VEE.

Related products
1/4W 5% Assorted Value Carbon Film Resistor Assortment Kit Set pack electronic diy kit
- 100% brand new and high quality.
- Fine workmanship and long service life.
- 1/4W carbon film resistor package.
- High precision and stability.
- Easy to use.
- Precision: 5%
- Error: 5%
- Values
- 10Ω, 15Ω, 22Ω, 33Ω, 47Ω, 68Ω, 100Ω, 220Ω, 330Ω, 470Ω, 1k, 1k5, 2k2, 3k3, 4k7, 5k6, 6K8, 8K2, 10K, 15K, 22K, 33K, 47K, 56K, 68K, 100K, 150K, 220K, 330K, 470K
- Package included: 150pcs
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
DC 50A 75mV Current Shunt Resistor for Amp Meter Gauge
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
GSM Antenna
GSM Antenna Dlenp 2dbi/3dbi Patch Antenna with SMA Male Connector
- GSM Antenna
- Gain: 2 to 3dbi
- Wire Length: 3 metre
- 3dbi Sticker Antenna
- GSM Antenna
- SMA Male Connector
- Frequency Range(MHz): 824-960/1710-1990Mhz
- Bandwidth (MHz): 136/280
- VSWR≤1.5
- Gain(dB): 2-3dbi
- Max Input power(W): 60W
- Input Impedance: 50 Ω
- Polarization Type: Vertical
- Cable Type: RG174
- Mounting Adhesive
- Net weight: 47g
SIM Card Holder
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.

Reviews
There are no reviews yet.