I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-19%
TNY279PN Off-line Switcher IC
Original price was: ₹80.00.₹65.00Current price is: ₹65.00. inc. GST
6 MHz 2 Pin Crystal Oscillator
₹21.00 inc. GST
TOP222YN Off-line PWM Switch IC
Original price was: ₹135.00.₹110.00Current price is: ₹110.00. inc. GST
- Supply Current: 1.2 mA
- Output Voltage: 5.7 V
- Power (Watts): 25W
- Output Current-Max: 0.5500 A
- Switching Frequency-Max: 110 KHz
- Lowest cost, lowest component count switcher solution.
- Â Cost competitive with linears above 5 W.
- Very low AC/DC losses – up to 90% efficiency.
- Â Built-in Auto-restart and Current limiting.
- Â Latching Thermal shutdown for system level protection.
- Â Circuit simplicity and Design Tools reduce time to market
- Package: TO-22
Description
TOPSwitch-II family introduced by Power Integrations designed as the latest generation of its industry-leading TOPSwitch series of off-line switcher ICs.The second generation TOPSwitch™-II family designed as the most cost effective and provides several enhancements over the first generation TOPSwitch family.TOP222Y Off-line PWM Switch IC designed explicitly for use in 100/115/230 VAC off-line Power Supply applications in the 100 to 150 W range. And also for 85-265 VAC off-line power factor correction (PFC) applications in the 50 to 90 W range. Many significant circuit enhancements that reduce the sensitivity to board layout and line transients now make the design even easier. These IC with internal lead frame utilize six of its pins to transmit heat from the chip directly to board. Thus eliminating the cost of a heat sink.
It is basically a complete integrated circuit consisting of only three pins with all functionalities for an off-line switched mode control system.These are high voltage N-channel power MOSFET featuring controlled turn-on gate driver, voltage mode PWM controller with integrated 100 kHz oscillator, high voltage start-up bias circuit. And also bandgap derived reference, bias shunt regulator/error amplifier for loop compensation and fault protection circuitry. This brings TOPSwitch technology advantages to many new applications, i.e. TV, Monitor, Audio amplifiers, etc. Meanwhile, it improves the efficiency, productivity and offers high reliability for the device.
TOPSwitch designed as a self biased and guarded linear control current-to-duty cycle converter with an open drain output. This IC acheives High efficiency through the utilization of CMOS and integration of the utmost number of functions possible. The CMOS significantly reduces bias currents as compared to bipolar or discrete solutions. Moreover, the Integration eliminates external power resistors utilized for current sensing and/or supplying initial start-up bias current.
Reviews (0)
Shipping & Delivery
Related products
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
Reviews
There are no reviews yet.