I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
Original price was: ₹7,525.00.₹5,000.00Current price is: ₹5,000.00. inc. GST
ULink2 ARM Emulator Programmer firmware Support MDK5.0 Cortex-M4 SWD
Original price was: ₹3,000.00.₹2,800.00Current price is: ₹2,800.00. inc. GST
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
Original price was: ₹350.00.₹300.00Current price is: ₹300.00. inc. GST
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
Description
This USBasp is an in-circuit serial electronic programmer designed for the Atmel AVR Microcontroller family. USBasp is a low-cost programmer that converts hex file (.hex) into an AVR microcontroller which consist of an Atmega8 microcontroller and a couple of passive components with a 12 MHz operating frequency of ATMega8. No special USB controller is required since the programmer uses a firmware-only USB driver.
In order to program a microcontroller we need to access four pins of the microcontroller, but our USB will have only two pins for communication, so how can we program a microcontroller with a USB. Here comes the functioning of the USB ASP Programmer. In short, a USBasp in-circuit serial programming adapter is used to install bootloaders and firmware on common AVR microcontrollers. In USBasp Target referred to as the board, we are programming. This module features an SCK option to support Targets with a low clock speed of less than 1.5MHz.
USBasp programmer with a 10-pin ISP connection provides the interface to the microcontroller at a programming speed of 5KB/sec. This USB interface is achieved by using an Atmega 8 processor and the rest is done in firmware. A 10-pin male header is used for various ISP header pins to make the interfacing easier. These are modules of compact size but with elegant design. This USB AVR programmer can be powered by an external power supply (target board) or from the USB Port Autospeed control function for flashing devices to get the best performance/stability.
The USBasp programmer will work with a wide variety of Atmel AVR microcontrollers including the Atmega8a and Atmega168a. The USBasp driver will work on both 32 and 64-bit platforms. As a result, a USBASP programmer works on multiple platforms such as Windows, Mac OS X, and Linux.
Free Comparable Boot Loaders:
- AVR SinaProg for Windows.
- AVRDUDE supports USBasp since version 5.2.
- BASCOM-AVR supports USBasp since version 1.11.9.6.
- Khazama AVR Programmer – An AVRdude GUI for MS Windows.
- eXtreme Burner – AVR is a Windows GUI Software for USBasp based USB AVR programmers.
- AVR Loader.
Reviews (0)
Shipping & Delivery
Related products
89C2051 Atmel Microcontroller IC
- Core Processor: 8051
- Data Bus Width: 8 bit
- Maximum Clock Frequency: 24 MHz
- Program Memory Size: 2 KB
- Program Memory Type: Flash
- Supply Voltage Range: 4 V to 6 V
- Package: PDIP-20
- Compatible with MCS-51™ Products
- 2K Bytes of Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles
- 7V to 6V Operating Range
- Fully Static Operation: 0 Hz to 24 MHz
- Two-level Program Memory Lock
- 128 x 8-bit Internal RAM
- 15 Programmable I/O Lines
- Two 16-bit Timer/Counters
- Six Interrupt Sources
- Programmable Serial UART Channel
- Direct LED Drive Outputs
- On-chip Analog Comparator
- Low-power Idle and Power-down Modes
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm
Pic Kit-2 Programmer
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit
- Type: Debugger/Programmer
- Tool/Board Application: Debugging/Programming
- MCU Supported Families: Flash-based PIC MCUs
- Core Architecture: PIC, dsPIC
- IC Product Type: In-Circuit Debugger
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Supports low voltage to 2.0 volts (2.0v to 6.0v range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of the microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Easy to use Windows-based programming
- USB Interface
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
- Model: TL866CS
- With a Multi-functional ICSP interface
- 40pin ZIF socket, fully automatic, support fast mode SPI
- USB interface for both data transfer and power supply
- With over-voltage and over current protection
- Supports the serial number of the chips two times development, built-in a variety of commonly used automatic numbering functions
- English Language Support
- It can program faster than another programmer 500%~1000%
- Programming EPROM, EEPROM, FLASH, SPI, I2C,93Cxx, ICSP etc.
- Supports thousands of most popular application devices (13071+)r
- Ideally suits the portable/convenient applications, which includes: car automotive field ECU chip tuning, airbag reset, mileage, satellite devices, BIOS refreshing, Xbox, Wii gaming machines EPROM sync, PIC / MCU development, newer laptop technology and newer desktop PC etc.
- Dimensions: 4.02 in x 2.48 in x 1.22 in (10.2 cm x 6.3 cm x 3.1 cm)
- Weight: 138 g
USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
Reviews
There are no reviews yet.