Showing 2197–2208 of 2263 results

Waveshare 5inch HDMI LCD (B) 800×480

₹4,500.00 inc. GST
  • 800x480 high hardware resolution
  • Resistive touch control
  • Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
  • When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
  • When working as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free
  • The backlight can be turned off to lower power consumption
  • 5mm audio jack speaker provided and supports HDMI audio output
  • Supports popular game consoles like Microsoft XBOX360 Sony PS4 and Nintendo Switch etc.
  • Multi languages OSD menu for power management brightness/contrast adjustment etc.
  • Also supports VGA input(specific cable is required and should be purchased separately)
  • Dimensions:18 x 10 x 9 cm
  • Weight: 200 Grams

Waveshare 7 inch Capacitive Touch Screen LCD 1024×600 HDMI interface

₹8,260.00 inc. GST
  • 7-inch IPS screen with a hardware resolution of 1024×600.
  • 5-points capacitive touch control.
  • Support backlight control, more power saving.
  • Supports popular mini PCs such as Raspberry Pi, Jetson Nano, BB Black, Banana Pi, as well as general desktop computers
  • When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
  • When working as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free
  • Supports popular game consoles like Microsoft XBOX360, Sony PS4, and Nintendo Switch, etc.
  • Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.
  • 5mm audio jack, speaker connector, supports HDMI audio output
  • Also supports VGA input(specific cable is required and should be purchased separately)
  • Dimension: 20 x 14 x 5 cm
  • Weight: 400 Grams

WeMos D1 ESP Wroom 02 Board ESP8266 Mini WiFi Nodemcu Module 18650 Battery

₹1,500.00 inc. GST
  • One AD inputs.
  • Micro USB inputs.
  • One programmable LED (D0).
  • AUTO PROGRAM circuit.
  • ESP8266 (ESP-WROOM-02 With TELEC) is equivalent to the NodeMCU.
  • Analog Input (AD): Built-in dividing resistor (AD = 220K ADC 100K = GND).
  • There is a SOLDER terminal for SLEEP MODE.
  • Compatible With Arduino andNodeMCU.
  • Operation and charging are possible at the same time.
  • 18650 charging circuit including the 5V boosting circuit with TP5410.
  • Overcharge protection, over-discharge protection built-in.
  • LED: Red = Charging, Green = Full charging.
  • 3000 mA 18650 It is possible to operate for more than 17 hours on a battery.
  • Integrated 18650 battery charging and discharging system.
  • One switch controls whether the 18650 battery is on power or not.
  • OLEDs SDA and SCL can connect to the D1 pin and the D2 pin respectively.
  • The five buttons can be controlled by FLATH, RSET, D5, D6, and D7 respectively.
  • The 5 Digital pins can configure the write/read/interrupt/PWM/I2C/one-wire supported separately.
  • Operation and NodeMCU consistent, adding a programmable LED, you can use GPIO16 to control; display 8266 running status and other functions. Integrated OLED and five buttons, more convenient for development.
  • The design concept originates from the open-source project NodeMCU; the development board integrates 18650 charging and discharging systems with charging and discharging protection. At the same time, an OLED and five directional buttons are integrated to facilitate the development.

WeMos D1 Lithium Battery Charger Board with Mini USB

₹475.00 inc. GST
  • Charging Voltage: max: 10V, recommend: 5V
  • Charging Current: max: 1A
  • Lithium Battery voltage: 3.3-4.2V
  • Boost Power Supply: 5V(max: 1A)
  • Can use  D1 mini without a USB cable, it's really wireless
  • Can use D1 mini anywhere, using this battery shield and a lithium Battery.
  • High reliability
  • Charging, when the battery run out, you do not need to unplug the battery, just use the USB port to charge.

Wemos D1 Mini ESP8266 NodeMCU WIFI board for Arduino

₹350.00 inc. GST
  • Microcontroller: ESP-8266EX
  • Operating Voltage: 3.3 V
  • Digital I/O Pins: 11
  • Analog Input Pins 1(Max input: 3.2V)
  • Clock Speed: 80MHz/160MHz
  • Flash: 4M bytes
  • Length: 34.2mm
  • Width: 25.6mm
  • Use BRT (Bias Resistor Transistor)
  • Easier into flash mode.
  • 30% increase in radiating area
  • Good stability.
  • 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
  • 1 analog input(3.2V max input)
  • Micro USB connection
  • Compatible with Arduino
  • Compatible with Node MCU
  • Support OTA wireless uploading
  • 11 x I/O pins,1 x ADC pin

WEMOS D1 Pro mini-16m External Antenna Connector ESP8266 WIFI Networking Smart Component

₹1,450.00 inc. GST
  • Input Voltage: 3.2V
  • Chip: ESP8266
  • 11 digital input/output pins
  • Interrupt/PWM/I2C/one-wire
  • 1 analog input(3.2V max input)
  • 16M bytes(128M bit) Flash
  • External antenna connector
  • Built-in ceramic antenna
  • New CP2104 USB-TO-UART IC
  • Dimension; 34*25*15mm
  • Weight: 8mm

Wemos D1 WiFi Esp8266 Development Board Uno Compatible Program

₹775.00 inc. GST
  • Microcontroller: ESP-8266EX
  • Operating Voltage: 3.3 V
  • Digital I/O Pins: 11
  • Analog Input Pins 1(Max input: 3.2V)
  • Clock Speed: 80MHz/160MHz
  • Flash: 4M bytes
  • Good stability.
  • 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
  • 1 analog input(3.2V max input)
  • Micro USB connection
  • Compatible with Arduino
  • Support OTA wireless uploading
11 x I/O pins,1 x ADC pin~!
  • On-Board Switching Power Supply:
-Input Voltage Range: 9V to 12V -Output: 5V at 1A Max
  • Micro USB connection
  • Compatible with Arduino
  • Support OTA wireless uploading

WH0201102 ABS 1.75 mm 1 kg Filament-Wanhao

₹1,500.00 inc. GST
  • Material: ABS
  • Color: White
  • Material Diameter: 1.75mm
  • Printing Temperature: 220° to 230°C
  • Roundness Accuracy: +/- 0.5mm +/- 0.5mm
  • Density: 1.31g/cm3 1.01g/cm3
  • Mounted: Spool Mounted
  • Net weight: 1kg
  • Packaging Vacuum-sealed with desiccant to protect the filament from humidity
  • Highly Detailed & Quality Outputs.
  • Tried and Tested by Makenica.com
  • Compatible with any FDM 3D Printer.
  • ABS is stronger than PLA
  • Easy to post-process.
  • Environment friendly – ISO 9001 and ROHS certified

White ABS 1.75 mm 1 KG Filament-Wanhao

₹1,700.00 inc. GST
  • Material: ABS
  • Color: White
  • Material Diameter: 1.75mm
  • Printing Temperature: 220° to 230°C
  • Roundness Accuracy: +/- 0.5mm +/- 0.5mm
  • Density: 1.31g/cm3 1.01g/cm3
  • Mounted: Spool Mounted
  • Net weight: 1kg
  • Packaging Vacuum-sealed with desiccant to protect the filament from humidity
  • Highly Detailed & Quality Outputs.
  • Tried and Tested by Makenica.com
  • Compatible with any FDM 3D Printer.
  • ABS is stronger than PLA
  • Easy to post-process.
  • Environment friendly – ISO 9001 and ROHS certified

White PLA 1.75 mm 1 KG Filament-Wanhao

₹1,700.00 inc. GST
  • High-quality starting material
  • Diameter tolerances of ± 0.1mm checked with laser monitor
  • Smooth surface with even rounding
  • Lower melting temperature
  • Good flow properties
  • Little odor development
  • Less risk of clogging the nozzle, compared to ABS
  • Compatible with almost all 1.75mm FDM printers
  • No heating bed necessary
  • High quality means less waste
  • Easy to use
  • No heating bed necessary Printing Settings:
  • Best Printing Temperature:200-220℃
  • Bed Temperature:0-70℃
  • Printing Speed:30~90mm/s
  • Movement Speed :90~150mm/s