I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Double speed measuring module encoder photoelectric pulse output module
₹180.00 Original price was: ₹180.00.₹150.00Current price is: ₹150.00. inc. GST
- Color: Green + black
- Material: FR4
- Working Voltage: 4.5~5.5V
- Launch Tube Pressure drop: V f=1.6V
- Launch Tube Current: I f<20mA
- Signal Output: A, B two lines
- TT Power Level
- Resolution: 0.01mm
- Measurement Frequency: 100 kHz
- D Type Holes Encoder Diameter: 24mm
- Encoder Resolution: 20 lines
- Speed measuring Sensor configuration: measure line 1 motor speed
Out of stock
This is Double Speed Measuring Module Two Speed Encoder Photoelectric Encoder Pulse Output Module HC – 020K. When combined with a black encoder, the switch output speed measurement module can measure motor speed. The HC-020K module, which has a broad voltage range, high resolution, and fast reaction time, is frequently used in the manufacture of high-precision encoders. This gadget uses a black encoder to measure the rotational speed of the motor (the encoder’s inner diameter is 4mm, therefore it may be used for motor output shafts with 4mm diameter, like the TT motor we matched, yellow shell and white axis).
The HC-020K Speed Encoder is a small module with an encoder disc for measuring motor speed. Furthermore, the module runs on 5V. And shows if there is a gap between the encoder and the reader at a frequency of 100kHz. It may also be used to determine the robot’s location. Although we must be aware that the motor rotation direction cannot be determined, we must always presume that the direction is the same as the ordered direction. There are just three pins on the module for connection, power, ground, and sensor output. To reduce the installed footprint, the right-angle header is mounted backwards.
PIN DESCRIPTION
- 5V – Connects to 5V on MCU
- GND – Connects to the ground on MCU
- OUT – Connects to a digital interrupt input or digital pin on MCU

Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
4*4 MATRIX KEYPAD
- The maximum current across each button: 3mA
- Easy communication with any microcontroller
- Ultra-thin design
- Adhesive backing provides easy integration
- High price-performance ratio
- Allows microcontroller to scan 8 output pins to check which 16 button
- Long life
- Maximum operating temperature: 0 degrees to 50 degrees Celsius
- Dimension: 70*77*1mm
- Weight: 7.5gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm
ISD1760 MODULE (75 sec)
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm
ISD1820 MODULE (10 SEC)
- Operating voltage: 2.6v to 5v
- Record and playback up to 10 sec
- Push-button and microcontroller controllable AGC circuit added tom increase audio playback volume
- Recording time: 8- 20 sec
- Built-in microphone
- On-chip 8-ohm speaker driver
- High quality, natural voice restored
- Available single-chip control audio recording control mode: the key to control or microcontroller, IO has drawn the line of control
- Can be used as propaganda module
- Auto power down mode
- Duration and sample rate can be extended to 20 sec by varying resistance
- Dimension: 43*34*11mm

Reviews
There are no reviews yet.