I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
5S0765 Power Switch IC
- Power Switch
- Drain Voltage: 650V
- Drain Current: 28A
- Supply Voltage: 30V
- Supply Current: 12mA
- Wide Operating Frequency Range Up to 150kHz
- Â Lowest Cost SMPS Solution
- Lowest External Components
-  Low Start-up Current (Max:170µA)
- Low Operating Current (Max:12mA)
- Â Internal High Voltage SenseFET
- Â Over Voltage Protection With Latch Mode (Min23V)
- Â Over Load Protection With Latch Mode
- Over Current Protection With Latch Mode
- Â Internal Thermal Protection With Latch Mode
- Pulse By Pulse Over Current Limiting
- Â Under Voltage Lockout With Hysteresis
- Â External Sync. Terminal
Description
Nowadays, Power devices defined as innovative technology enabling future development of power converters and systems. These Power Device IC capable of precisely controlling electrical energy from the source to the load according to the load demand, at high efficiency, and with outstanding reliability. A power device IC designed as a semiconductor device acts as a switch in power electronics (ex: switch-mode power supply). Such a type of device known as the power device. Or when used in an integrated circuit, referred to as the power IC.
The 5L0380 Power Switch IC designed as an integrated Sense FETs designed explicitly for high-performance offline Switch Mode Power Supplies (SMPS) operated with minimal external components. These devices integrated as high voltage power switching regulators with a low Start-up Current Max of 170µA and low Operating Current of Max 12mA . It features Under Voltage Lock Out (UVLO) protection, Over Voltage Protection With Latch Mode (Min23V). And also optimized gOver Load Protection With Latch Mode, Internal Thermal Protection With Latch Mode, Pulse By Pulse Over Current Limiting.
Applications
- SMPS for VCR, SVR, STB, DVD & also DVCD
- SMPS for Printer, Facsimile & Scanner
- Adaptor for Camcorder
Reviews (0)
Shipping & Delivery
Related products
25pcs Button Switch Kit
- Relative Humidity: 95%
- Rated Voltage: 12V
- Rated Current: 50 mA
- Contact resistance: 50M Ohm Max (initial)
- The insulation resistance: 100M Ohm minDC (250V)
- The compressive strength: AC250V (50/60Hz for 1 minute)
- Mechanical life: 100000 cycles
- The environment temperature: 25° ~ + 105°
- The operating strength: 180/250 (plus or minus 30gf)
- Dimension: 12 * 12 * 7.3 round convex type
- Total Buttons: 25pcs
- Colours: 5 (Black, Red, White, Blue, Yellow)
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
Reviews
There are no reviews yet.