HC-06 4Pin Bluetooth Module Without Reset Switch
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Dormancy current: no dormancy.
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
HC-06 Bluetooth Module
- Input Supply voltage: 3.6 - 6V
- Input current: 50 (mA)
- Maximum Operating Range: 10m
- Operating Frequency: 2.4GHz ISM band
- Modulation: GFSK (Gaussian Frequency Shift Keying)
- Emission power: 4dBm, Class 2
- Sensitivity: -84dBm at 0.1% BER
- Operating Temperature: -20 ~ +75 degree C
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps (Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
HC-06 RF Wireless Bluetooth Bee V2.0 Module Xbee V03 Shield Board Arduino
- Power supply: 3.3V
- A power supply of more than 3.3V will destroy the module.
- Paring user’s name: HC-05
- Default baud rate: 9600
- Default slave model
- Default pairing password: 1234
- It can be used for an MCU system whose voltage is 3.3V.
- Users can set baud rate, paring password, and user’s information by AT command.
- Bluetooth adapter pairs with Bluetooth Bee salve device.
- With an efficient onboard antenna, the exposed antenna qualifies the transmit signal and make it farther.
- Be used with for Arduino Bluetooth Bee module, it can communicate with other Bluetooth device wireless
- Be used with Xbee module to achieve communication between more than two for Arduinos or communication between for Arduino and PC
- Dimension: : 3.3 x 2.5 x 0.9 cm
- Weight: 5g
HC-12 433 SI4463 Wireless Serial Module
- IEEE 802.15.4g compliant
- Supply voltage: 3.2V~5.5V
- Operating frequency range: 433.4-473.0MHz,
- Up to 100 channels of communication
- Receive sensitivity = –126 dBm
- Serial TTL (RX, TX, GND) interface
- Modulation (G)FSK, 4(G)FSK, (G)MSK, OOK
- Maximum transmit power: 100mW (settable)
- Max output power: +20 dBm
- Low active power consumption: 10/13 mA RX, 18 mA TX at +10 dBm
- Ultra-low current power-down modes: 30 nA shutdown, 50 nA standby
- Data rate: 100 kbps to 1 Mbps
- Fast wake and hop times
- The highly configurable packet handler
- TX and RX 64 byte FIFOs
- Auto frequency control (AFC)
- Automatic gain control (AGC)
- Low BOM and battery detector
- Default factory settings: Mode FU3, the baud rate is 9600bps, communication channels CH001 (433.4M)
HC-12 SI4463 TTL LoRa Module
HC-SR04 ultrasonic distance sensor transparent
HC-SR04 ultrasonic range finder module
HC-SR501 PIR Motion Detector Sensor module
HC-SR505 Mini Infrared PIR Motion Sensor Infrared Detector Module
- Model: HC-SR505
- Operating Voltage Range: DC4.5-20V
- Average Current Consumption (mA): 0.06
- Distance Measuring Range: 3 meters
- Delay time: Default 8S + -30% (can be customized)
- Working Temperature Range: -20°C ~ 80°C
- Sensor Lens Diameter: 10mm
- Induction angle: <100-degree cone angle
- Low-power consumption
- Output level: High 3.3V / Low 0V
- Trigger: repeatable trigger (default)
- Automatic induction: to enter the sensing range of the output is high, people leave the sensor range automatically delay off high, output low
- Dimensions: 10 x 23 x 5mm
- Weight: 10gm
HCZ-H8-B Humidity Sensor, HCZ Series, 20% to 90% RH, 3 %, Through Hole, No Housing
HDMI Male to VGA Female Converter Adapter 1080P For PC, Rspberry Pi
- Support HD resolution, super clear picture, fast transmission speed
- The maximum signal range up to 1920 X 1200, 1080p;
- Video input signal: 5Volts p-p(TTL) ;
- Support VGA video bandwidth: 10 bit, 162MHz
- Video amplifier bandwidth: 162MHz
- Support resolution up to 1920 X 1200, reduce blank signal during transmit.
- No external power supply, plug, and play.
