LDR SENSOR 20mm
LDR SENSOR 5mm
MOQ: 2 nos
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800C (Approx.)
- Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 5mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
lead acid battery capacity indicator
LEAD ACID BATTERY RECHARGEABLE 1.3A 12V
Lead Copper Nut 8mm
Leadshine DM320C
- Supply voltage up to +30 VDC
- Output current programmable, from 0.3A to 2.0A
- Pulse input frequency up to 70 kHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Self-test and Auto-configuration technology offers optimum responses with different motors
- Microstep resolutions programmable, from full-step to 102,400 steps/rev
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
Leadshine DMA860H
- Input voltage: Up to +80VAC or +110VDC.
- Output current Up to 7.2A.
- Pulse input frequency up to 300 KHz.
- Automatic idle-current reduction.
- Over-voltage, over-current protection.
- Suitable for 2-phase and 4-phase motors.
- Support PUL/DIR and CW/CCW modes.
- Operating Temperature : 70 C.
- High performance, cost-effective
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
Leap Motion Controller
- Power supply: 5V DC via USB connector (minimum 0.5A)
- Data connection: USB 2.0
- Interaction zone: Depth of up to 60cm (24”) preferred, up to 80cm (31”) maximum;
- 140×120° typical field of view.
- 3 LEDs spaced on either side and between the cameras, baffled to prevent overlaps.
- Construction: Aluminium and scratch-resistant glass
- Operating temperature: 32º to 113º F (0º to 45ºC)
- Storage temperature: 14º to 122º F (-10º to 50º C)
- Relative Humidity: 5% to 85% (non-condensing)
- Two 640x240-pixel near-infrared cameras; spaced 40 millimetres apart infrared-transparent window, operate in the 850 nanometre +/-25 spectral range; typically operates at 120Hz; capable of image capture within 1/2000th of a second.
- Highly accurate hand and finger tracking with near-zero latency
- 135° field of view extending above the device
- Orion SDK compatible with Windows 7 or newer
- Updated V4 tracking
