MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
Magnetic Contactor TC1-D25 10
Magnetic Door Open Sensor – N/C Type
- Max Voltage: 100V DC
- Max Rated power: 10W
- Sensing Distance: 15-25mm
- Wire lead: 24 Awg, about 350mm long
- Rated Current: 100mA
- Connecting mode: N.C. (Normally closed)
- Easy to install
- Strong concealment
- Magnetic sensor alarm, control the switch of the circuit via the built-in magnet
- Alarm when someone intrudes into your places
- Can be used in places like apartments, hotels, offices, etc.
- Ideal for residential or commercial use.
- Designed to do embedded in the door or window frame.
- Dimension: approx. 27 x 14 x 8mm
Male Solenoid Valve Connector
MALE TO FEMALE JUMPER WIRES
MALE TO MALE JUMPER WIRES
MANTIS CLAW EAGLE CLAW ARM
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
MAX 8550 SMD Rework Station , Micro Soldering Station , Hot Air Soldering & Desoldering Station
MAX30102 Heart Rate Oxygen Pulse Breakout Sensor Module For Arduino
- Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End
- Optical Heart-Rate Monitor and Pulse Oximetry Solution
- Measures absorbance of pulsing blood
- I2C interface plus INT pin
- Tiny 12.7mm x 12.7mm (0.5in x 0.5in) Board Size
- Highly integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-Low-Power Operation Increases Battery Life for Wearable Devices
- Programmable Sample Rate and LED Current for Power Savings
- Ultra-Low Shutdown Current (0.7µA, typ)
- Advanced Functionality Improves Measurement Performance
- High SNR Provides Robust Motion Artifact Resilience
- Integrated Ambient Light Cancellation
- High Sample Rate Capability
- Fast Data Output Capability
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm